background image

12

Prepare For Your Next Garden

Use only water and mild soap when 

cleaning your AeroGarden (except 

when Sanitizing - Step 7). Do not use 

abrasive cleaners or run through the 

dishwasher.

!

Sanitize AeroGarden.  
• Fill Bowl ¾ full with water.
• Add ¼ cup (59ml) of chlorine 

bleach.

• Replace Grow Surface on Bowl

place Bowl on Base and plug in 

AeroGarden for 1-2 minutes.  

(Select Salad Greens on Control 

Panel to be sure water is flowing.)

• Unplug AeroGarden and empty 

bleach water from Bowl.

Rinse AeroGarden.  
• Refill Bowl with tap water and 

replace on Base.

• Plug in and run AeroGarden  

for 1-2 minutes. (Select Salad  

Greens again.)

• Empty Bowl and repeat this step 

(step 8) one more time.

Towel dry the Bowl and Grow  

Surface before putting them back 

together and setting them back on  

the Base.

If your Grow Bulbs have been in use 

more than 6 months, they should be 

replaced at this time. 

Your AeroGarden is now ready for 

replanting.

Unplug AeroGarden.

Carefully remove Bowl and 

Grow Surface from the Base  

and bring to a sink. 
Set Base and Lamp Hood aside.
NEVER SUBMERSE BASE AND 

CONTROL PANEL IN WATER.

Remove Grow Surface  from  

Bowl and place on a counter 

near a sink. 

Empty contents of Bowl in sink.

Remove Seed Pods and plants 

from Grow Surface.  
• Pull Seed Pods out of Grow 

Surface openings.

• Throw away Seed Pods and 

plant debris (plant growth and 

roots). If you compost, plant 

debris can be composted.

Rinse and clean Grow Surface, 

Pump Stand and Pump Filter*.
• Use a soft scrub brush to clean 

tangled roots from underside of 

Grow Surface and Pump Stand. 

• Remove Pump Filter from 

Pump Stand. Gently scrub 

roots from Pump Filter.

• Place Pump Filter back into 

Pump Stand.

After cleaning, there may still be a few 

roots in your Grow SurfacePump Stand 

or Pump Filter. This will not affect the 

operation of your AeroGarden.

1

2

3

4

5

6

9

7

8

10

11

* IMPORTANT NOTE: We recommend replacing the Pump Filter after growing two gardens. 

Order Pump Filters from

 www.aerogardensupport.com 

or from your retailer.

Pump

Stand

Pump

Filter

Plant 

Growth

Seed

Pod

Roots

Grow

Surface

Grow

Surface

Bowl

Base

Lamp

Hood

cleaning and Storage Instructions for your AeroGarden

When your garden has completed its growing cycle…

Содержание 100629

















Отзывы: