background image

GUIDE#: pwb-ASSAULT-004

2

This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths.  

 

 

• 

This measurement is taken from the Port to Starboard mounting points. 

Do not fold the tower without having the top section securely fastened to the side sections with 

• 

the fasteners provided.

Lubricate the telescopic side section tubes that slide in and out of the top section during instal-

• 

lation. We recommend using a light grease to help the tubes slide together without binding.

Do not fold the tower by yourself.

• 

Do not assemble tower on the ground and then try to install it on the boat.

• 

Do not use impact drivers to install any hardware.

• 

Torque set screws to 35ft-lbs 

• 

Torque shoulder bolts 50 ft-lbs 

• 

Torque tower foot all-thread to 65 ft-lbs

• 

We recommend using red Loctite threadlocker on the threads of all fasteners that will not be 

• 

adjusted while lowering or raising the tower.

Check the top section for burr’s before installing side sections to prevent the scratching and 

• 

marking of tubes.

 Aerial does not cover damage caused by burr’s during installation.

If the area of the deck where the tower will be mounted has a fiberglass thickness of less than 

• 

¼ inch, a backing plate kit must be purchased and installed to provide adequate support.

Please leave the foam wrap on the tower until the installing is complete.

• 

Please note that when towing your boat you may notice what appears to be movement in 

• 

your tower.  It is important to understand that the boat is also moving on the trailer and that this 

movement can be visually deceiving. 

Frequently wash your tower with soap and water.

• 

As required, use Mothers Mag & Aluminum polish to restore your tower to its original finish.

• 

BE CAREFUL when assembling this product

• 

. We CANNOT be liable for any burring or scratch-

ing that may occur when sliding sections in and out of each other.

NEVER modify this product in any way.

• 

NEVER climb, stand or ride on this product.

• 

NEVER tow watersport tubes or inflatable’s with this or any other Aerial Wakeboard Tower.

• 

ALWAYS use caution with approaching bridges or overpasses.

• 

ALWAYS inspect this product for loose bolts, fittings or damage before each use.

• 

Always carefully CONSULT the user manual for proper installation, maintenance and usage.

• 

Aerial is not liable for personal injury or property damage from the use of this or any other 

• 

Aerial product.

IMPORTANT INFORMATION

cleaning

WaRning

Содержание Assault Wakeboard Tower














Отзывы: