background image

4

3.5 Rating label

Fig.3.c

 Rating label

3.4 Space required

Make sure that enough space is left around the unit to allow easy maintenance (access to filters, terminal box and removal of the 

side and front inspection panels).

To set the RIGHT orientation of the machine:

• Modify the orientation on the CTRL-DSP (point 7.2 - Installer menu: 3 Machine Orientation).

• Replace the ducting connection label on the top of the casing and the water drainage label on the bottom of the casing with 

those supplied with this installation manual.

Fig. 3.b

 Connections in RIGHT orientation

    Intake air from outside

    Exhaust air to outside

    Supply air to inside

    Extract air from inside

    Winter condensation drainage

    Summer condensation drainage

A

B  

D

C

F

E

4 traNsPort aND storagE

The appliance is delivered in one carton box.

The appliance should be stored and transported in such a way that it is protected against physical damage that can harm spigots, 

casing, display etc.

It should be covered so that dust, rain and snow cannot enter and damage the unit and its components.

5 INstallatIoN

This section describes how to install the unit correctly.

The unit must be installed according to these instructions.

5.1 Unpacking

Verify that the unit (and eventual accessories) delivered is according to order before starting the installation. Any discrepancies 

from the ordered equipment must be reported to the supplier.

5.2 Where/how to install

• 

All QR units are meant for indoor installation in a heated space. 

• Mount the unit on flat surface (wall).

• 

The unit must always be installed vertically.

• 

It’s important that the unit is completely leveled before it is put into operation.

• Place the unit preferably in a separate room (e.g. storage, laundry room or similar).

WARNING

Make sure that specific warnings and cautions in Chapter 2 “Precautions” are carefully read, understood and applied!

WARNING

Make sure that specific warnings and cautions in Chapter 2 “Precautions” are carefully read, understood and applied!

F

E

A

B  

C

D

Содержание QR350ABP

























Отзывы: