ELECTRICAL SPECIFICATIONS
Nominal Range:
10A
Measurement Range:
0.1 to 12A
Transformation Ratio:
Voltage output
Output Signal:
100mV/A (1V at 10A)
Accuracy and Phase Shift*:
Accuracy:
0.1 to 0.5A:
2.5% Reading ± 0.1mV
0.5 to 1A:
2.5% Reading
1 to 12A:
1% Reading
Phase Shift:
.01 to 0.1A: Not Specified
0.1 to 1A:
5°
1 to 5A:
3°
5 to 12A:
2.5°
*Reference conditions: 20°C to 26°C, 20 to 75% RH,
external magnetic field <40A/m, 48 to 65Hz sine wave,
distortion factor less than 1%, no DC component, no
external current carrying conductor, test sample centered.
Load impedance > 1M
.
Frequency Range:
40 to 10kHz
Limit Operating Conditions:
20A permanently to 10kHz;
Derating above 10kHz: 20A x 0.1F (in kHz)
Crest Factor:
3 @ 10Arms with an error (due to CF) of 3%
Working Voltage:
600Vrms
Common Mode Voltage:
600Vrms
Influence of Adjacent Conductor:
< 15mA/A at 50Hz
Influence of DC on AC signal:
DC Current < 2A, < 5%
Influence of Conductor Position in Jaw:
0.5% of mV output @ 50/60Hz
Influence of Frequency:
40Hz to 1kHz: 0.5% of mV output
1kHz to 10kHz: 2% of mV output
Influence of Temperature:
150ppm/°K, or 0.15% of mV output per 10°K
Influence of Humidity (10 - 90% RH):
0.2% of mV output per 10°K @ 18° to 28°C
MECHANICAL SPECIFICATIONS
Operating Temperature:
14° to 131°F (-10° to +55°C)
Storage Temperature:
-40° to 158°F (-40° to +70°C)
Operating Relative Humidity:
10° to 35°C 85% RH
(without roll-off above 35°C)
Maximum Cable Diameter:
One Ø 0.78" (20mm), bus bar 20 x 5mm
Case Protection:
IP 40 (IEC 529)
Drop Test:
Test per IEC 68-2-32:
1.0m drop on 38mm of Oak on concrete.
Mechanical Shock:
Test per IEC 68-2-27
Vibration:
Test per IEC 68-2-6
Dimensions:
5.47 x 2.00 x 1.18" (139 x 51 x 30mm)
Weight:
180g (6.5oz)
Polycarbonate Material:
Jaws: Polycarbonate with 10% fiberglass charge,
Red UL 94 V0
Case: Polycarbonate 920A Gray
Opening Operations - Life:
> 50,000
Output:
Double/reinforced insulated 5 ft (1.5m) lead with
safety 4mm banana plug
SAFETY SPECIFICATIONS
Electrical:
Double insulation or reinforced insulation between
the primary or secondary and the outer case of the
handle conforms to IEC 1010-2-32.
Dielectric Strength:
IEC 1010-2-32, Category III, Pollution Degree 2
5550V, 50/60 Hz between primary, secondary
and the outer case of the handle
Electromagnetic Compatibility:
EN 50081-1 Class B
EN 50082-2 Electrostatic discharge
IEC 1000-4-2
Radiated field IEC 1000-4-3
Fast transients IEC 1000-4-4
Magnetic field at 50/60 Hz IEC 1000-4-8
ORDERING INFORMATION
AC Current Probe MN307 ................. Cat #2116.23
Accessories:
Banana plug adapter
(to non-recessed plug) .......................
Cat #1017.45
E192383
2.56"
(65 mm)
5.47"
(139 mm)
.83"
(21 mm)
Black
Red
.73"
2.00"
(51 mm)
(18.5 mm)
.1.18"
(30 mm)
Tactical
Barrier
(keep hands below
this barrier)
MN306 MN307
