AEM 30-0300 Скачать руководство пользователя страница 1

P/N 30-0300

X-SERIES UEGO GAUGE

Bosch LSU4.9

AEM Performance Electronics, 2205 126th Street Unit A, Hawthorne, CA 90250 - Phone: (310) 484-2322

http://www.aemelectronics.com

STOP! - READ THIS BEFORE INSTALL OR USE!

WARNING:
THIS INSTALLATION MAY REQUIRE WELDING OR INTEGRATION INTO A VEHICLE'S ELECTRICAL SYSTEM.  DAMAGE
TO SENSITIVE ELECTRONICS, FIRE, OR EXPLOSION MAY OCCUR IF PROPER PRECAUTION IS NOT TAKEN.  IF THERE
IS ANY DOUBT, 

DO NOT

 ATTEMPT THE INSTALLATION AND CONSULT A PROFESSIONAL.

NOTE

: IT IS THE RESPONSIBILITY OF THE ENGINE TUNER TO ULTIMATELY CONFIRM THE CALIBRATION USE FOR

ANY PARTICULAR ENGINE IS SAFE FOR ITS INTENDED USE.  AEM HOLDS NO RESPONSIBILITY FOR ANY ENGINE
DAMAGE THAT RESULTS FROM THE MISUSE OF THIS PRODUCT.

Instruction

Manual

The 52mm (2-1/16”) AEM X-Series Universal Exhaust Gas Oxygen (UEGO) Gauge features a four digit central readout and
sweeping 24-color-coded LED display, providing immediate reference to the engine air fuel ratio (or lambda) in real-time.
The AEM gauge is ideal for all vehicles including carbureted applications and engine dynamometers. A 0-5V analog output
is included and can be used with data loggers or aftermarket ECUs including the AEM Infinity Engine Management
System (EMS).  In addition, an AEMnet (CAN bus) and serial data stream are also available for logging or mixture control
purposes.

The X-Series Digital Wideband technology is US Patent #9,575,030.

Features

·

X-Digital Technology

·

Free air or resistor trim calibration modes

·

Fast response, 20ms typical

·

2-1/16" / 52mm outer diameter mounting

·

8.0:1 to 20.0:1 AFR / 0.55 to 2.00 Lambda

·

Configurable 3 or 4 digit precision display mode

·

Lambda, AFR, O2 % display modes with reversible
faceplate

·

Black bezel/faceplate supplied; Silver/white available
as optional purchase

·

Locking connectors

·

Supports vehicle/system voltages up to 16V

·

Supports Bosch LSU4.9 Sensor

·

0-5V Analog Output

·

AEMnet (CAN bus) Output

·

Serial RS-232 Output

KIT CONTENTS

PN

Description

10-0300

INST, X-SERIES UEGO GAUGE

35-0300

GAUGE ASSY, X-SERIES AFR GAUGE

-

RED INSULATED BUTT CONNECTORS (4)

35-4005

WELD-IN BUNG,02 SENSOR 1214 MILD STEEL

35-8618

NUT, KNURLED, M4x0.7 (2)

35-8614

BRACKET, X-SERIES GAUGE

35-3430

PWR/IO CABLE, X-SERIES GAUGE

35-3427

SENSOR CABLE, X-SERIES GAUGE LSU4.9

35-8617

RUBBER BAND, X-SERIES GAUGE

35-2004

SENSOR, WIDEBAND UEGO BOSCH LSU 4.9

*OPTIONAL* ACCESSORIES

PN

Description

30-0300-ACC

BEZEL, X-SERIES GAUGE SILVER

FACEPLATE, X-SERIES AFR WHITE

30-2355-200

NO WELD UEGO CLAMP KIT, 1.75" to 2.00"

30-2355-250

NO WELD UEGO CLAMP KIT, 2.25" to 2.50"

30-2355-300

NO WELD UEGO CLAMP KIT, 2.75" to 3.00"

30-2355-350

NO WELD UEGO CLAMP KIT, 3.25" to 3.50"

30-4008

WELD-IN FINNED BUNG, O2 LONG, STAINLESS STEEL

35-4001

BUNG PLUG,02 SENSOR

Содержание 30-0300














Отзывы: