AEM 21-699 Скачать руководство пользователя страница 13

Страница: 13 / 14

f. Install the edge trim (8-6016) onto the lower lip

and sides of the cold air hood scoop’s inlet. Ensure

the edge trim is even on both sides of the inlet and

is fully seated; use the heel of your hand or a light

rubber mallet to fully seat.

g. Open the vehicle’s hood. Mount the AEM

cold

air hood scoop onto the underside of the hood by

mounting the plastic push rivets (8-174) into the 4

insulator pad mounting holes by hand. Ensure the

4 push rivets are fully seated and properly secure

the AEM

hood scoop in place. Make sure the

edge trim of the AEM

hoop scoop inlet fully seals

around the cutout in the underside of the vehicle

hood.

h. In some vehicles, you may need to unclip the

windshield washer hose under the hood to prevent

the hose from being pinched. Re-route the hose

around the back of the new hood scoop and then

re-clip the hose.

AEM

intake system installed

Содержание 21-699















Результаты поиска

Содержание 21-699

Отзывы:

Похожие инструкции для 21-699

Бренды по названию

Популярные бренды

AEM 21-699, Инструкции по установке

Результаты поиска

Содержание 21-699

Отзывы:

Похожие инструкции для 21-699

Бренды по названию

Популярные бренды