AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя | Manualshive

Страница: 103 / 120

background image

103

Brightness

The Brightness setup dialog allows you to choose two different brightness
settings for both the screen and LEDs. See

Harness and Wiring

section for

Night Mode input wiring. 100% should only be used in direct sunlight. 70% gives
almost as much brightness without overdriving the backlight. 5%-10% is
appropriate for night mode.

NOTE: The LEDs used in the CD-5 unit are

brighter and may require different settings compared to a CD-7 unit.

Count Up and Count Down Timers

The output channels Count Up Timer and Count Down Timer are configured in the Setup Editor.  In the outputs tab,
check Show Predefined Outputs to display these channels for editing along with all other existing predefined
channels.  The output channel Count Up Timer can be added to a layout and set in msf format (minutes-seconds-
hundredths).  The Count Up Timer will increment continuously unless reset by pressing the right dash button.  Count
Down Timer can be added to a layout and configured in hmsf format (hours-minutes-seconds-hundredths).  Click on
the "..." button in the Primary Input column of the Outputs tab to edit the Count Down Timer reset values.  The Count
Down Timer will reset to its starting time by pressing the right dash button.

«
...
101
102
103
104
105
...
»

Содержание CD-5 Carbon

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CD-5 Carbon

Бренд: Daga Страницы: 28

Бренд: Wallenstein Страницы: 31

Бренд: Happy Orange Страницы: 2

Бренд: IBS Страницы: 24

Бренд: Panasonic Страницы: 1

Event Master E2

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 7

Бренд: Barco Страницы: 7

Titanium Series

Бренд: Fass Страницы: 13

Бренд: Tailfin Страницы: 8

StudSensor HD25

Бренд: Zircon Страницы: 2

Бренд: APEXi Страницы: 18

Бренд: Prorack Страницы: 15

Бренд: PROAIM Страницы: 3

PSEN sg2c-5CCLLE

Бренд: Pilz Страницы: 52

Бренд: Home Accents Holiday Страницы: 2

Бренд: Metra Electronics Страницы: 4

REARSIGHT OnStar 250-8822

Бренд: Rostra Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды