12
13
EN
refrigerator temperature.
• Immerse the cappuccino maker in the milk container (fig.
23), taking care not to immerse it for more than half its
length.
• Press the
icon (B12) (fig. 22) (take care to avoid scalds).
“STEAM PRESS OK” is displayed.
• Press the OK icon (B9).
• To interrupt steam delivery, press the
icon (B12) again
or the ESC icon (B6).
Steam comes out of the cappuccino maker. For a creamier
froth, immerse the cappuccino maker in the milk and move
the container with slow upward movements. You should
not deliver steam for more than 2 minutes at a time.
• When the required froth is reached, interrupt steam deli-
very by pressing the
icon (B12) again or the ESC icon
(B6).
• Make the coffee as described above using sufficiently large
cups, then fill them with the frothed milk prepared pre-
viously.
IMPORTANT: always clean the cappuccino system immedia-
tely after use. Proceed as follows:
• Press the
icon (B12) and then press the OK icon (B9) to
discharge a small amount of steam for a few seconds. This
empties the steam spout of all traces of milk.
IMPORTANT: to ensure the hygiene of the appliance, you
are recommended to carry out this procedure each time
you make cappuccino to avoid stale milk remaining in the
circuit.
• Wait for the cappuccino maker to cool down, then holding
the cappuccino maker lever firmly in one hand, unscrew
the cappuccino maker itself with the other, turning it an-
ticlockwise and removing it downwards (fig. 24).
• Remove the cappuccino maker nozzle by pulling it down-
wards.
• Wash the cappuccino maker and nozzle thoroughly in hot
water.
• Make sure the two holes shown in figure 25 are not blo-
cked. If necessary, clean with a pin.
• Replace the nozzle by inserting it upwards into the cappuc-
cino maker.
• Replace the cappuccino maker by pushing it upwards and
rotating it anticlockwise.
MAKING A NUMBER OF CUPS OF
COFFEE WITH THE JUG FUNCTION
• Using this function you can automatically make a number
of cups of coffee (4, 6) directly in the jug (A27) to keep the
coffee hot.
• Turn the jug lid until the arrow lines up with the word OPEN
and remove the lid.
Rinse the jug and lid.
• Close the jug by turning the lid towards CLOSE until it is
tightly closed and then place it under the coffee spout.
Always position the jug with the handle facing to the right
or left as shown in the figure.
The coffee spout (A13) must be fully raised to enable the
jug to be inserted.
“FILL BEAN CONT. AND WATER TANK, EMPTY WASTE CONT.,
PRESS OK” is displayed. Make sure the water tank is full, the
bean container is full enough and the waste coffee contai-
ner is completely empty.
• Press the OK icon (B9).
The type of coffee selected, for example “EXTRA-MILD JUG”,
and the number of cups you want to make with the jug are
displayed, for example “JUG 4 CUPS”.
• Confirm by pressing the icon (B14). The display shows
a progress bar which indicates coffee making process.
When the progress bar is complete, the appliance finishes
the process and automatically goes back to the coffee jug
function. If on the other hand an incomplete progress bar is
displayed, this means that the cycle has not been comple-
ted correctly. Remove the jug and check the message which
appears on the display, consulting the section “DISPLAYED
MESSAGES”.
• Remove jug and leave the lid in the CLOSE position to keep
the coffee hot.
• To pour the coffee, turn the lid anticlockwise until the arrow
is lined up with the spout of the jug.
Important!
When the coffee beans are insufficient to
complete the required function, the appliance stops the process
and waits for the bean container to be filled again and the
icon (B14) to be pressed. For example, when you want to make 4
cups of coffee but the beans are insufficient, the appliance ma-
