AEG L1815R, Оригинальное руководство пользователя

Страница: 4 / 8

4
4
temperature is more than 10°C but less than 37°C. To reduce the
risk of serious personal injury, do not store outside or in vehicles.
■
Under extreme usage or temperature conditions, battery
leakage may occur. If liquid comes in contact with the skin, wash
immediately with soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into the eyes, flush them with clean water
for at least 10 minutes, then seek immediate medical attention.
Following this rule will reduce the risk of serious personal injury.
OPERATION
Use the battery pack for AEG 18V c ordless products only.
LITHIUM-ION BATTERY PACKS
Lithium-ion batteries deliver fade free power for their entire run time.
Lithium-ion tools will not gradually lose power due to decreasing
battery charge. Instead, power from the battery pack will drop from
full to zero once the full charge has been drained from the battery.
Once this happens, recharging of the battery is required. It is not
necessary to drain the battery pack completely before recharging.
BATTERY PROTECTION FEATURES
Battery packs are designed with features that monitor and protect
the lithium-ion cells (active, standby, shut off and sleep modes) and
maximize battery life.
The tool may stop during use to prevent overheating or overloading
of the battery (active mode). In this case, release the trigger to reset
and resume operation.
If this does not reactivate the tool, the battery is completely
discharged (stand-by or sleep mode) and needs to be charged in a
compatible charger.
The battery can be recharged in stand-by or sleep mode. It is not
necessary to completely discharge the battery pack before recharging.
AEG battery packs are equipped with an additional SHUT-OFF mode,
minimizing self discharge of the battery while the battery is not in
use. It will be reactivated automatically when used with a tool or by
pressing the LED gauge
COLD WEATHER OPERATION
The lithium-ion battery pack can be used in temperatures down to
-1
0°C. Put the battery pack on a tool and use the tool in light duty
application. After a while, the battery pack will warm up and begin
operating normally.
CHARGING THE BATTERY PACK
Battery packs are shipped in a low charge condition to prevent
possible problems. Therefore, they should be charged prior to first
use.
NOTE: If the charger does not charge the battery pack under normal
circumstances, return both the battery pack and charger to the
nearest authorised service centre for electrical check.
Charge the battery pack only with the recommended charger.
Battery pack Compatible charger
L1815R
L1825R
L1830R-X5
L1840R
L1850R
L1860R
L1860R-X5
L1890R
AL18G
AL1218G
BL1218
BLK1218
BL18DP-X5
BL18DP2-X5
BL18DPS
BL1418
WARNING! Only charge in compatible AEG 18V chargers.
Use of other chargers may result in fire, danger or serious
personal injury.
■
Press down on the battery pack to ensure contacts on the battery
pack engage properly with the contacts in the charger.
■
Connect the charger to the power supply. Make sure it is the
required power supply.
■
Make sure the latches on each side of the battery pack snap
into place and the battery pack is secured in the charger before
beginning operation.
■
Place the battery pack in the charger aligning raised rib on the
battery pack with the groove in the charger.
■
The battery pack will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.
NOTE: Do not place the charger and battery pack in an area of
extreme heat or cold. They will work best at normal room temperature.
■
Place charger on hard surface not soft (carpet, etc.), when
charging batteries.
■
When batteries become fully charged, unplug the charger from
power supply and remove the battery pack.
■
To remove battery pack from the charger, depress the latches on
each side of the battery pack.
■
After normal usage, a minimum of 1 hour charging time is required
to fully recharge the battery pack.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the battery pack may become hot.
A hot battery pack may be placed directly onto the charger port but
charging will not begin until the battery temperature cools to within
acceptable temperature range. When a hot battery pack is placed on
the charger, the charger may indicate the pack is not ready to charge.
Please refer to charger operator’s manual. When the battery pack
cools, the charger will automatically begin charging.
CHARGING A COOL BATTERY PACK
A cold battery pack may be placed directly onto the charger port but
charging will not begin until the battery temperature warms to within
acceptable temperature range. When a cold battery pack is placed on
the charger, the charger may indicate the pack is not ready to charge.
Please refer to charger operator’s manual. When the battery pack
warms, the charger will automatically begin charging.
CHARGE STATUS
To display the amount of charge left in the battery, press the Charge
level indicator button.