26
2.5)
If the hood is to be used as a
filtering
hood, it is necessary to purchase carbon filters
(see ACCESSORIES).
3 MOUNTING INSTRUCTIONS
ATTENTION
! The hood is equipped with standard fixing material. The person
who is mounting the hood should make sure that the fixing elements are right and
suitable for the walls and ceiling he finds. The manufacturer declines any responsibility
for damages caused by incorrect mounting.
3.1 DISMANTLING AND RE-POSITIONING OF THE GREASE FILTERS
To mount the hood or insert the carbon filters, it is necessary to gain access to the inside,
therefore the grease filters should be removed.
Attention: some cooker hoods are equipped with blind grease filters for side suction that cover
the real grease filters; in these cases before removing the grease filters it is necessary to take
away the blind filters by gripping them from the side and pulling them downwards. (Fig.5).
TO EXTRACT a grease-filter (see direction of arrow in FIG.5):
•
pull the lever and take the grease filter out pulling it downwards.
TO RE-POSITION the grease-filter (SEE FIG.5 opposite direction to the arrow):
•
insert the back side of the grease filter into its groove;
•
pull the lever downwards and insert the front part of the filter;
•
release the lever and make sure that the pin of the handle enters into its hole.
3.2 FITTING AND REMOVAL OF EVENTUAL CARBON FILTERS
If you wish to use the hood as a filtering hood, it is necessary to fit the carbon filters.
The carbon filters which contain activated carbon ARE OPTIONAL, and can be bought
separately.
It is available a kind of carbon filter that can be regenerated for which the mounting and use
instruction are given separately with the filter. (see Fig.6c).
We have 2 different kinds of carbon filters not regenerable which are described as follows.
Once you have dismantled the grease filter, it is possible to recognize the kind of filter used in
the hood (see FIG.6).
In case the mounted filter is the one shown in FIG.6a
, follow the following procedure for
mounting:
•
pay attention to the shape of the joints;
•
insert the back side into its groove;
•
lift the front side of the carbon filter, until it is blocked in position;
•
clamp the filter by rotating the 2 knobs at 90°.
To remove a carbon filter proceed as follows: (see FIG.6A, opposite direction of arrows):
•
rotate the two knobs at 90°;
•
pull the front side of the filters downwards;
•
fully extract, by removing the back of the filter from the groove.
In case the carbon filters used are the ones shown in Fig. 6b
, (pair of filters), proceed as
follows for mounting:
•
grip the external part of the filter (the convex one);
•
lay the filter on the side of the motor so that the joints in alu can enter the grooves;
•
rotate the filter 60 ° in the direction shown by the arrow;
•
to be sure that the filter is correctly installed, try to move this from the motor to the
outside. If it does not move, it means it has been correctly fitted.
Repeat the above for the other filter
To remove both carbon filters proceed as follows for both of them (see FIG.6b, DIRECTION
OPPOSITE TO THE ARROW):
•
grasp the external part of the filter;
Содержание ELECTROLUX EFC9740.2X
