AEG APP10, Оригинальное руководство пользователя

Страница: 27 / 28

27
27
■
Run the engine until it stops. This will remove all the fuel that could
become stale and leave varnish and gum in the fuel system.
■
When transporting the product in a vehicle, secure the product against
movement or falling to prevent injury to persons or damage to the
product.
■
Never carry or transport the product while the engine is running.
■
Abide by all government and local regulations for the safety storage and
handling of petrol.
SHORT TERM (LESS THAN ONE MONTH)
■
Turn off the engine and allow the engine to cool before storing.
FOR ASSEMBLING WITH ELECTRIC-DRIVEN POWER HEAD
■
Turn off the product, disconnect the product from the power supply,
and wind the cable. Allow the product to cool down before storing or
transporting.
FOR ASSEMBLING WITH BATTERY-DRIVEN POWER HEAD
■
Turn off the product, remove the battery pack, and allow the product to
cool down before storing or transporting.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries must be done in accordance with local,
national, and international provisions and regulations.
■
The user can transport the battery packs by road without further
requirements.
■
Commercial transport of lithium-ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons, and the
process must be accompanied by corresponding experts.
When transporting battery packs:
■
Ensure that the battery contact terminals are protected and insulated to
prevent short circuit.
■
Ensure that the battery pack is secured against movement within
packaging.
■
Do not transport battery packs that are cracked or leaking.
Check with the forwarding company for further advice.
MAINTENANCE
WARNING! Use only original manufacturer’s replacement parts,
accessories, and attachments. Failure to do so can cause possible injury, can
contribute to poor performance, and may void your warranty.
WARNING! Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. Have the product serviced
by an authorised service centre only. When servicing, use only original
replacement parts.
WARNING!
The saw chain is very sharp. To prevent personal injury,
exercise extreme caution when cleaning, fitting, or removing the chain
scabbard. Always wear protective gloves when performing maintenance on
the chain.
WARNING! Improper chain maintenance increases the potential of
kickback. Failure to replace or repair a damaged chain can cause serious injury.
■
Turn off the product and remove the battery pack before conducting any
maintenance or cleaning work.
■
You may make adjustments or repairs described in this manual. For other
repairs, contact an authorised service centre.
■
Follow instructions for lubricating and chain tension checking and
adjustment.
■
After each use, clean the body and handles of the product with a soft,
dry cloth.
■
Check all the nuts, bolts, and screws at frequent intervals for proper
tightness to ensure that the product is in safe working condition. Any part
that is damaged should be properly repaired or replaced by an authorised
service centre.
Maintenance schedule
The bar may be reversed to distribute wear for maximum life. The bar should
be cleaned every day of use and checked for wear and damage.
Daily check
Bar lubrication Before each use
Chain tension Before each use and frequently
Chain sharpness Before each use, visual check
For damaged parts Before each use
For loose fasteners Before each use
Fuel mixture or fuel and lubricant
(only for petrol-driven power head)
Before each use
Clutch engagement (only for petrol-
driven power head) (no chain
movement at idling speed)
Before each use
Power cable for damage (only for
electric-driven power head)
Before each use
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to completely
eliminate certain residual risk factors. The following hazards may arise during
use, and the operator should pay special attention to avoid the following:
■
injury caused by vibration
–
Hold the product by the designated handles, and restrict working
time and exposure.
■
injury caused by exposure to noise
–
Wear hearing protection, and limit exposure.
■
injury from contact with the exposed saw teeth of the chain
■
injury caused by kickback or sudden and unforeseen movement of the
guide bar
■
injury caused by ejected parts of the saw chain
■
injury caused by thrown-off parts of the workpiece (wood chips and
splinters)
■
injury caused by dust and particles
■
injury caused by skin contact with the lubricant or oil
RISK REDUCTION
It has been reported that vibrations from handheld tools may contribute
to a condition called Raynaud’s Syndrome. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent upon exposure
to cold. Hereditary factors, exposure to cold and dampness, diet, smoking,
and work practices are all thought to contribute to the development of the
symptoms. There are measures that can be taken by the operator to possibly
reduce the effects of vibration:
■
Keep your body warm in cold weather. When operating the product, wear
gloves to keep the hands and wrists warm. It is reported that cold weather
is a major factor contributing to Raynaud’s Syndrome.
■
After each period of operation, exercise to increase blood circulation.
■
Take frequent work breaks. Limit the amount of exposure per day.
If you experience any of the symptoms of this condition, immediately
discontinue use and see your physician.
WARNING! Injuries may be caused, or aggravated, by prolonged use of a
tool. When using any tool for prolonged periods, ensure that you take regular
breaks.
KNOW YOUR PRODUCT
See pages 4–5.
■
Oil reservoir cap
■
Bar bolt
■
Chain
■
Bar
■
Branch hook
■
Chain tensioning screw
■
Attachment shaft
SYMBOLS
Safety alert
Read and understand all instructions before operating the
product. Follow all warnings and safety instructions.
Wear eye, ear, and head protection.
Wear non-slip safety footwear when using the product.
Wear non-slip, heavy duty gloves.
Do not expose the product to rain or damp condition.
10m
Electrical hazard, at least 15 m away from the overhead
electric-power lines
106
Guaranteed sound power level
Minimum
120mm
Keep hands at least 120 mm away from the chain.
Beware of thrown or flying objects. Keep all bystanders,
especially children and pets, at least 15 m away from the
operating area.
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
Regulatory Compliance Mark (RCM). Product meets
applicable regulatory requirements.