background image

10

10

DRIvE DEPTH ADjUSTmENT

See figure 9.

The driving depth of the nail may be adjusted by rotating the 

dial  clockwise  to  increase  or  counterclockwise  to  decrease 

the  depth  the  nail  is  driven.  It  is  advisable  to  test  the  depth 

on a scrap workpiece to determine the required depth for the 

application and to drive a test nail after each adjustment until 

the desired depth is set.

REmOvING NAIlS FROm THE TOOl

See figure 10.

 

■ Remove the battery pack from the tool.

 WARNING!

Remove the battery pack from the tool before removing nails. 

Failure to do so could result in serious personal injury.

 

■ To remove a strip of nails from the tool, hold the finish nailer 

by the handle with your right hand, and rest your left hand 

underneath the tool with your left thumb on the pusher.

 

■ Depress the inside lever on the pusher to release and allow 

the pusher to slowly slide to the front. 
NOTE: Always keep fingers clear of nail track of magazine 

to prevent injury from unintended release of the pusher.

 

■ Slide  the  nails  toward  the  back  of  the  magazine  and 

remove.

ClEARING A jAmmED FASTENER

See figure 11.

 WARNING!

 

■ Remove the battery pack from the tool before clearing a 

jammed fastener. Failure to do so could result in serious 

personal injury.

If a nail or fastener becomes jammed in the tool, remove the 

battery pack and keep the tool pointed away from you while 

clearing the jam.

 

■ Remove the battery pack from the tool.

 

■ Remove fasteners from the tool.

 

■ Pull up on the latch and open the jam release.

 

■ Insert a flat blade screwdriver into the driving mechanism 

and push the driver mechanism back, freeing the fastener 

jam.

 

■ Remove the bent fastener.

 

■ Close the jam release and latch.

 

■ Reinstall the battery pack.

 

■ Reinstall fasteners and close the magazine.

mAINTENANCE

Use  only  AEG  accessories  and  spare  parts.  Should 

components  need  to  be  replaced  which  have  not  been 

described, please contact one of our AEG service agents (see 

our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please 

state  the  Article  No.  as  well  as  the  machine  type  printed  on 

the label and order the drawing at your local service agents or 

directly at: AEG Electric Tools, Max-Eyth-Straße 10, D-71364 

Winnenden, Germany.

SymbOlS

Please  read  the  instructions  carefully  before 

starting the machine.

Remove  the  battery  pack  before  starting  any 

work on the machine.

Do not dispose of electric tools together with 

household  waste  material!  In  observance  of 

European  Directive  2002/96/EC  on  waste 

electrical  and  electronic  equipment  and  its 

implementation  in  accordance  with  national 

law,  electric  tools  that  have  reached  the  end 

of  their  life  must  be  collected  separately  and 

returned  to  an  environmentally  compatible 

recycling facility.

Содержание AFNDA18













Отзывы: