background image

2

2

LED Functions

Charge Status

0 - 25%

25 - 50%

50 - 75%

75 - 100%

 

If four LEDs glow orange, the battery pack is fully charged. 

The battery pack capacity is between 75%-100%.

 

If three LEDs glow orange and one is off, the battery pack 

capacity is between 50%-75%.

 

If  two  LEDs  glow  orange  and  the  other  two  are  off,  the 

battery pack capacity is between 25%-50%.

 

If only one LED glows orange and others are off, the battery 

pack capacity is lower than 25%. In this case, the battery 

pack can be used as usual until automatically turned off by 

the control program.

BAtteRy PRotectIoN feAtuReS

AEG 58V LITHIUM-ION batteries are designed with features 

that protect the LITHIUM-ION cells and maximise battery life. 

If the tool stops during use, the following may be the causes:

a.  The maximum current draw of the battery has been 

exceeded, causing it to automatically stop powering 

the tool. Release the trigger to reset the tool and pull 

the trigger to resume operation.

b.  Excessive temperatures will cause the battery to stop 

powering the tool. Feel the battery pack; if it is too 

warm, allow it to cool down. 

If the tool still does not work, recharge the battery.

Note:

  The  battery  pack  indicator  LED  will  not  work  if  the 

battery  protection  feature  has  caused  the  battery  pack  to 

stop powering the tool. Release the tool trigger or remove the 

battery pack from the tool and the battery pack LED indicator 

will resume normal function.

cHARGING tHe BAtteRy PAck

Battery packs are shipped in a low charge condition to prevent 

possible  problems.  Therefore,  you  should  charge  them  until 

the green LED on the front of the charger comes on.
If the charger does not charge the battery pack under normal 

circumstances,  return  both  the  battery  pack  and  charger  to 

your nearest authorised service centre for electrical check.

to cHARGe:

 

Use battery pack only with the recommended charger.

 

Connect the charger to the power supply. Make sure the 

power supply is normal household voltage, 220-240 volts, 

AC only, 50-60 Hz.

 

Make sure the latch of the charger snap into place and the 

battery  pack  is  secured  in  the  charger  before  beginning 

operation.

 

Slide the battery pack along the groove of the charger.

 

Press down on the battery pack to be sure contacts on the 

battery pack engage properly with contacts in the charger.

 

Do not place the charger and battery pack in an area of 

extreme heat or cold. They will work best at normal room 

temperature.

 

Note:

 The charger and battery pack should be placed in 

a  location  where  the  temperature  is  more  than  10°C  but 

less than 38°C.

 

The  battery  pack  will  become  slightly  warm  to  the  touch 

while  charging.  This  is  normal  and  does  not  indicate  a 

problem.

 

After  charging  is  complete,  the  charger  green  LED  will 

remain on until either the battery pack has been removed 

from the charger or the charger has been removed from 

the power supply.

 

After charging is complete, the battery pack indicator LED 

will remain on 1 min then turn off. But if the battery pack 

has been removed from the power supply, the battery pack 

indicator LED will turn off.

 

When batteries become fully charged, unplug the charger 

from the power supply and remove the battery pack.

 

To remove the battery pack from the charger, depress the 

latch of the charger.

cHARGING A Hot BAtteRy PAck

If  the  battery  pack  is  above  normal  temperature  range,  the 

charger red LED will begin flashing and the green LED will be 

off. When the battery pack cools down to approximately 50°C, 

the charger will automatically begin fast charge mode.

cHARGING A cooL BAtteRy PAck

If  the  battery  pack  is  below  normal  temperature  range,  the 

charger red LED will begin flashing and the green LED will be 

off.  When  the  battery  warms  to  a  temperature  of  more  than 

0°C, the charger will automatically begin charge mode.

coLD WeAtHeR oPeRAtIoN 

The LITHIUM-ION battery pack can be used in temperatures 

down to -20°C. Put the battery pack on a tool and use the tool 

in a light duty application. After about a minute, the pack will 

have warmed up and begin operating normally.

BAtteRIeS

These  batteries  have  been  designed  to  provide  maximum 

trouble-free life. However, like all batteries, they will eventually 

wear  out.  Do  not  disassemble  battery  pack  and  attempt  to 

replace  the  batteries.  Handling  of  these  batteries,  especially 

when wearing rings and jewelry, could result in a serious burn.
To  obtain  the  longest  possible  battery  life,  we  suggest  the 

following:

 

Remove the battery pack from the charger once it is fully 

charged and ready for use. For battery pack storage longer 

than 30 days:

• 

Store the battery pack where the temperature is below 

27°C and away from moisture.

• 

Store battery packs in a 30%-50% charged condition.

• 

Every six months of storage, charge the battery pack 

as normal.

BAtteRy PAck ReMoVAL AND PRePARAtIoN foR Re-

cycLING

To  preserve  natural  resources,  please  recycle  or  dispose  of 

batteries properly.

Содержание ABP58LI401









Отзывы: