AE Techron 2105, Руководство оператора

Страница: 5 / 46

List of Figures
Figure 1.1 – 2105 Front Panel ....................................................................................................... 6
Figure 3.1 – Close-up of the Output Terminal Resistor .................................................................. 9
Figure 3.2 – Controlled Voltage Hookup ........................................................................................ 9
Figure 3.3 – Close-up of SIM card ................................................................................................. 9
Figure 3.4 – Input Select switch functions on the Input Terminals ............................................... 10
Figure 3.5 – Close-up of AC Mains Outlet ................................................................................... 10
Figure 3.6 – Sample of Configurations Setting Label .................................................................. 10
Figure 4.1 – Power Switch ........................................................................................................... 11
Figure 4.2 – Gain Control ............................................................................................................. 11
Figure 4.3 – Push Buttons ........................................................................................................... 11
Figure 4.5 – Main Status Indicators for Stand-Alone Amplifiers ................................................... 12
Figure 4.4 – Main and Fault Status Indicators ............................................................................. 12
Figure 4.6 – Fault Status Indicators for Stand-Alone Amplifiers .................................................. 13
Figure 4.7 – Main Status Indicators for Multi-Amplifier Systems ................................................. 14
Figure 4.8 – Fault Status Indicators for Multi-Amplifier Systems ................................................. 15
Figure 4.9 – Back Panel Controls and Connectors ...................................................................... 16
Figure 5.1 – Access Panel Screw Locations ................................................................................ 17
Figure 5.2 – Main Board Location Inside Access Panel ............................................................... 17
Figure 5.3 – Master/Slave Setting ................................................................................................ 18
Figure 5.4 – Gain Trim Control ..................................................................................................... 18
Figure 5.5 – Controlled-Voltage/Controlled-Current Mode Setting .............................................. 19
Figure 5.6 – Compensation Setting ............................................................................................. 19
Figure 5.7 – Run Mode/Stop Mode on Power-Up Setting ............................................................ 20
Figure 5.8 – Standby Mode on Over Load Setting ....................................................................... 20
Figure 5.9 – Accessing the Power Supply Board ......................................................................... 21
Figure 5.10 – Location of Amplifier High-Voltage Transformer Sockets ....................................... 21
Figure 5.11 – J3 and J7 Plug Locations for High-Current Output ................................................ 21
Figure 5.12 – J4 and J8 Plug Locations for High-Voltage Output ................................................ 21
Figure 5.13 – Bi-Level Power Switch Location ............................................................................ 22
Figure 6.1 – Input to Output Comparison, Controlled-Voltage Operation .................................... 23
Figure 6.2 – Input to Output Comparison, Controlled-Current Operation .................................... 23
Figure 6.3 – Factory-installed Default RC Network ...................................................................... 24
Figure 6.5 – Compensation Effects on Waveform ....................................................................... 26
Figure 6.4 – Custom Compensation Location .............................................................................. 26
Figure 6.6 – Square Wave Showing a Decrease in R is Required .............................................. 26
Figure 6.7 – Square Wave Showing an Increase in R is Required .............................................. 26
Figure 6.8 – Square Wave Showing an Increase in C is Required .............................................. 26
Figure 6.9 – Remote Status and Control Pinouts ........................................................................ 27
Figure 6.10 – Remote Status and Reset Schematic .................................................................... 28
Figure 6.11 – Remote Run/Standby Monitor ................................................................................ 29
Figure 6.12 – Remote Enable/Standby ........................................................................................ 30
Figure 6.13 – Remote Current Monitoring ................................................................................... 30
Figure 6.14 – Remote Current Monitoring, Alternate Method ...................................................... 31
Figure 6.15 – Blanking Activation ................................................................................................. 31
Figure 7.1 – Board-Level Functional Block Diagram ................................................................... 36
Figure 9.1 – +Vcc and –Vcc Point Locations ............................................................................... 38
Figure 9.2 – Fuse F1 Location ..................................................................................................... 39
Figure 9.3 – Interlock I/O Connector ............................................................................................ 39