●
The MONITOR OUT terminal output can be switched for NTSC or PAL monitors.
Installation Guide
Network Camera
Model No.
P-24
PGQX1914ZA avs0615-0 Printed in China
●
This manual describes the installation procedures, network camera installation, cable connec-
tions, and the angle of view adjustment.
●
Before reading this manual, be sure to read the Important Information.
Major operating controls
The component names of the camera are as follows. Refer to the illustration when installing or
adjusting the camera.
Standard accessories
Making connections
Important Information ............................... 1 pc.
Installation Guide (this document) ............ 1 set
CD-ROM
*1
................................................. 1 pc.
Code label
*2
.............................................. 1 pc.
*1 The CD-ROM contains the operating instructions and different kinds of tool software pro-
grams.
*2 This label may be required for network management. The network administrator shall retain
the code label.
The following parts are used during installation procedures.
Ⓐ
Base bracket ........................................ 1 pc.
Ⓒ
Fixing screws for attachment plate
(M4 x 8 mm) ...................................... 5 pcs.
(of them, 1 for spare)
Ⓖ
Template B (for the base bracket) .. 1 sheet.
Ⓘ
2P power cable ..................................... 1 pc.
Ⓚ
Waterproof tape ................................... 1 pc.
Ⓑ
Attachment plate .................................. 1 pc.
Ⓓ
4P alarm cable ..................................... 1 pc.
Ⓔ
MONITOR OUT conversion plug ......... 1 pc.
Ⓕ
Template A (for the attachment plate) 1 sheet.
Ⓗ
Bit ......................................................... 1 pc.
Ⓙ
LAN connector cover ........................... 1 pc.
Ⓗ
Ⓚ
●
How to initialize the camera
Follow the steps below to initialize the network camera.
1
Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the cam-
era. When using an external power supply, disconnect the 2P power cable plug from the camera.
2
Turn on the power of the camera while holding down the INITIAL SET button, and then keep
holding down the button for 5 seconds or more. The camera will start up after about 2 minutes
of taking off the INITIAL SET button and the settings including the network settings will be
initialized.
●
When data is being sent via the network camera
Blinks green (accessing)
Turn off each system’s power supply before making a connection. Before making connections,
prepare the required peripheral devices and cables.
●
When the camera is able to communicate with the connected device Lights orange
●
When an SD memory card*
1
is inserted and could
Lights off → Blinks green →
be recognized
Lights off
● When data can be saved after the SD memory card is
Lights off → Lights green
inserted and the SD ON/OFF button is pressed
●
When data can be saved to the SD memory card
Lights green
●
When the SD memory card is removed after holding down
Lights green → Blinks green → Lights off
the SD ON/OFF button for about 2 seconds
(recording)
Lights green → Lights off
(waiting for recording)
●
When data cannot be saved to the SD memory card because Lights off
an abnormality was detected or the SD memory card is
configured not to be used
●
When AF (Auto Focus) operation is being executed
Blinks red (Interval of 1 time/ second)
●
When the set is being started
Lights red
● When an SD memory card is recognized normally
Lights red → Lights off
●
When an abnormality is detected in both SD1 and SD2
Lights red → Stays red
cards after the camera has started
● When an abnormality is only detected in the SD1 card Lights red → Blinks red
after the camera has started
(Interval of 1 time/ 3 seconds)
● When an abnormality is only detected in the SD2 card
Lights red → Blinks red
after the camera has started
(Interval of 2 times/ 3 seconds)
IMPORTANT:
●
When the camera is initialized, the settings including the network settings will be initial-
ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not
be initialized.
●
Before initializing the settings, it is recommended to write down the settings in advance.
●
Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
IMPORTANT:
●
This is valid if the [Monitor out] is set to [Switch priority] ([Switch priority] is selected by
default). For details, refer to the Operating Instructions (included in the CD-ROM).
IMPORTANT:
●
Use all 4 pairs (8 pins) of the LAN cable (category 5e or better, straight).
●
The maximum cable length is 100 m {328 feet}.
●
Make sure that the PoE device in use is compliant with IEEE802.3af standard.
●
When connecting both the 12 V DC power supply and the PoE device for power
supply, 12 V DC will be used for power supply*.
* If a 12 V DC power supply and a PoE hub or router are used at the same time,
network connections may not be possible. In this case, disable the PoE settings.
Refer to the operating instructions of the PoE hub or router in use.
* Depending on the PoE device used, if you stop the 12 V DC power supply after
operating it and a PoE hub or router at the same time, the power supply may stop,
causing the camera to restart.
●
When the LAN cable is disconnected once, reconnect the cable after around 2 seconds.
When the cable is quickly reconnected, the power may not be supplied from the PoE
device.
●
When cables are used outdoors, there is a chance that they may be affected by
lightning. In this case, install a lightning arrester just before where the cables con-
nect to the camera.
Connect a LAN cable (category 5e or better, straight)
Waterproof treatment for the cable joint sections
When connecting to a network using a PoE hub
Microphone/line input cable
Connect a monaural mini plug (ø3.5 mm {1/8 inches}).
● Input impedance: Approx. 2 kΩ (unbalanced)
●
Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)
Less than 10 m {32.8 feet} (for line input)
●
Recommended microphone: Plug-in power type (option)
●
Supply voltage: 2.5 V ±0.5 V
●
Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
●
Input level for the line input: Approx. –10 dBV
IMPORTANT:
●
Be sure to use the 4P alarm cable provided with this product.
●
When using the EXT I/O terminals as the output terminals, ensure they do not cause
signal collision with external signals.
●
Install external devices so that they do not exceed the ratings above.
Connect the alarm input/output cable
<Ratings>
•
ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3
Input specification: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF:
Open or 4 V - 5 V DC
ON:
Make contact with GND (required drive current: 1 mA or more)
• ALARM OUT, AUX OUT
Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open:
4 V - 5 V DC by internal pull-up
Close:
Output voltage 1 V DC or less (maximum drive current: 50 mA)
*
The default of EXT I/O terminals is “Off”.
Connect an external amplifier-embedded speaker to the audio output cable
Connect a stereo mini plug (ø3.5 mm {1/8 inches}) (Audio output is monaural.).*
● Output impedance: Approx. 600 Ω (unbalanced)
●
Recommended cable length: Less than 10 m {32.8 feet}
●
Output level: –20 dBV
IMPORTANT:
●
Connect/disconnect the audio cables and turn on the power of the camera after turn-
ing off the power of the audio output devices. Otherwise, loud noise may be heard
from the speaker.
●
Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conver-
sion cable (mono-stereo).
Adequate waterproof treatment is required for the cables when installing the camera with cables
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are
not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to ap-
ply waterproof treatment in the following procedure. Failure to observe this or use of a tape other
than the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in
malfunction.
Before starting the installation, check the entire system configuration. The following illustration
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
<LAN cable>
< Alarm input/output cable, power cable, micro-
phone/line input cable, audio output cable>
Wind the tape in a
half-overlapping manner.
Wind the tape in a
half-overlapping
manner.
Wind the tape in a
half-overlapping manner.
Wind the tape in a
half-overlapping
manner.
IMPORTANT:
How to wind the supplied waterproof tape
●
Also waterproof the 2P power cable (accessory), 4P
alarm cable (accessory), and external connections in
the same way.
●
Stretch the tape by approx. twice (see the illustration)
and wind it around the cable. Insufficient tape stretch
causes insufficient waterproofing.
●
To prevent the LAN cable hook from coming loose
easily, fit the
Ⓙ
LAN connector cover onto the pigtail
cable as illustrated, and then slide it in the direction
indicated by the arrow.
The connector of the LAN cable used with this cam-
era must meet the following restrictions.
Height when inserted (From bottom to hook.):
Max. 16 mm {5/8 inches}
Connector width: Max. 14 mm {9/16 inches}
●
To install this product outdoors, be sure to waterproof
the cables. Waterproof grade (IEC IP66 or equiva-
lent) is applied to this product only when it is installed
correctly as described in these operating instructions
and appropriate waterproof treatment is applied. The
internal parts of base brackets are not waterproofed.
2x
Stretch the tape to
about twice.
PoE device (hub)
PC
LAN cable
(category 5e or
better, straight)
Adjustment monitor
LAN cable
(category 5e or better,
straight)
LAN cable
(category 5e or better,
straight)
Powered speaker
Microphone
Powered speaker
Microphone
Adjustment monitor
Recommended total
extended cable length*
IMPORTANT:
●
The adjustment monitor is used for checking the adjustment of the angular field of view
when installing the camera or when servicing. It is not provided for recording/monitoring use.
●
Depending on the monitor, some characters (camera title, preset ID, etc.) may not be
displayed on the screen.
●
Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
●
If a PoE hub is not used, each network camera must be connected to a 12 V DC
power supply.
●
When using 12 V DC, power supply from a PoE hub or router is not required.
INITIAL SET button
Dehumidifying
device
Auto focus (AF) button
SD slot 1 (SD1)
SD slot 2 (SD2)
SD ON/OFF button
•
FRONT must posi-
tioned in front of the
camera (on the
advidia logo side).
Direction marker
for installation
(FRONT )
Direction marker for installation ( TOP)
●
Points up when installing to a wall.
Dome cover
Light-blocking rubber ring
IR LED
Azimuth adjustment ring Tilting table
Panning table
Camera fixing screw
The hook engages
with the connector
terminal
Ⓙ
LAN connector cover
Ⓒ
Fixing screws for
attachment plate
(accessory)
Enclosure
(Screw size 6.35 mm
{1/4 inches} torx wrench)
Camera
Ⓑ
Attachment
plate (accessory)
Ⓐ
Base bracket
ACT indicator
LINK indicator
SD MOUNT indicator
SD ERROR/AF indicator
*1 SDXC/SDHC/SD memory card is described as SD memory card.
MONITOR OUT terminal
(factory shipment: NTSC
monitor)
D
4P alarm cable (accessory)
GND (black)
ALARM IN3, AUX OUT (gray) (Terminal 3)
ALARM IN2, ALARM OUT (red) (Terminal 2)
ALARM IN1, DAY/NIGHT IN (green) (Terminal 1)
Connect the output cable of the AC adaptor to the 2P power cable.
Power cable
12 V DC
Red
Positive
Black Negative
<Required cable>
LAN cable (category 5e or better, straight)
Use a LAN cable (category 5e or better, cross) when directly connecting the camera to a PC.
* Recommended cable length from the speaker: less than 10 m {32.8 feet}
Recommended cable length from the microphone: less than 1 m {3.28 feet}
*
Use an external powered
speaker.
Connect the power cable
IMPORTANT:
●
The 12 V DC power supply shall be insulated from the commercial AC power.
●
Be sure to use the 2P power cable provided with this product.
●
Be sure to fully insert the 2P power cable into the 12 V DC power supply terminal.
Otherwise, it may damage the camera or cause malfunction.
●
When installing the camera, make sure that excessive force is not applied to the
power cable.
●
Be sure to use an AC adaptor compliant with the specifications(written in the indication
label on the bottom side of this unit) regarding power source and power consumption.
Caution:
●
A READILY ACCESSIBLE DISCONNECT DEVICE SHALL
BE INCORPORATED TO THE EQUIPMENT POWERED
BY 12 V DC POWER SUPPLY.
●
ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
UL/CSA 60950-1).
Included Installation Instructions
© advidia 2015
WIDE button
(moves the camera to the “Wide” side)
TELE button
(moves the camera to the “Tele” side)
2P power cable (accessory)
RJ45 (female)Network cable
Alarm input/output cable
Microphone/line input cable (white)
Audio output cable (black)
LAN cable (category 5e or better
straight)
4P alarm cable
(accessory)
Power cable
(12 V DC)
12 V DC (red)
GND (black)
Screen display
top (TOP)
NTSC/PAL switch
advidia
5120 Woodway, Suite 5006
Houston TX, 77056
(832) 240-1768
http://advidia.com/
Caution:
●
Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur-
ing the setting. Refer to the Operating Instructions on the provided CD-ROM for fur-
ther information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings (“Off”,
“Alarm input”, “Alarm output” or “AUX output”).
