Advantech PPC-L158T Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 59

background image

9

PPC-L158T User Manual

Chapter 2

S

ystem

Setup

2.2

Preparing for First-time Use

Before commencing set up of the panel PC system, the following items should be
available:



Keyboard



Mouse (for system software installation)

2.3

Installation Procedures

2.3.1 Connecting the Power Cord

The panel PC can be powered through an AC electrical outlet (100 ~ 250 volts,

50 ~ 60 Hz) or DC outlet (15 ~ 24 V). Be sure to handle the power cords by holding
the plug ends only. Follow these procedures in order:

1.

Connect the female end of the power cord to the AC/DC inlet of the panel PC.

2.

Connect the 3-pin male plug of the power cord to an electrical outlet.

2.3.2 Connecting the Keyboard and Mouse

Connect the mouse and keyboard to the I/O section of PPC. If using a serial mouse
and the panel PC has a touchscreen, it is possible to connect the mouse to any COM
port.

2.3.3 Switching on the Power

Switch on the power switch, which is located inside the bottom side cover.

2.4

Running the BIOS Setup Program

The panel PC will be properly set up and configured by the dealer prior to delivery.
However, it may be necessary to use the panel PC's BIOS (Basic Input-Output Sys-
tem) setup program to change the system configuration information, such as the cur-
rent date and time, or the type of hard drive. The setup program is stored in read-only
memory (ROM). It can be accessed either when you turn on or reset the panel PC, by
pressing the ‘Del’ key on your keyboard immediately after powering on the computer.

The settings specified with the setup program are recorded in a special area of mem-
ory called “CMOS RAM”. This memory is backed up by a battery so that it will not be
erased after turning off or resetting the system. Whenever the power is turned on, the
system reads the settings stored in CMOS RAM and compares them to the equip-
ment check conducted during the power on self-test (POST). If a problem occurs, an
error message will be displayed on screen, and the computer prompts the user to run
the setup program.

2.5

Installing System Software

Recent releases of operating systems from major vendors include setup programs
which load automatically and guide you through hard disk formatting and operating
system installation. The guidelines below will help determine the steps necessary to
install the operating system onto the panel PC hard drive.

Note!

Some distributors and system integrators may have already pre-
installed system software prior to shipment.

«
...
17
18
19
20
21
...
»

Содержание PPC-L158T




























































Отзывы:

Нет отзывов

Похожие инструкции для PPC-L158T

Бренд: CanadianSolar Страницы: 19

Бренд: AMX Страницы: 1

Бренд: Waterboy Страницы: 19

GOT3217WL-845-PCT

Бренд: AXIOMTEK Страницы: 44

Бренд: Canadian Solar Страницы: 11

Бренд: 2M Technology Страницы: 35

Бренд: Sony Страницы: 5

Бренд: Sony Страницы: 2

WEGA KLV-S32A10

Бренд: Sony Страницы: 2

WEGA KLV-S26A10

Бренд: Sony Страницы: 2

WEGA KLV-S20G10

Бренд: Sony Страницы: 2

WEGA KLV-S23A10

Бренд: Sony Страницы: 2

WEGA KLV-S23A10

Бренд: Sony Страницы: 2

WEGA KLV-S20G10

Бренд: Sony Страницы: 2

WEGA KLV-S19A10

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 31

Бренд: Sony Страницы: 39

WEGA KLV-S19A10

Бренд: Sony Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды