manualshive.com logo in svg

Advantech PCL-858, Руководство пользователя

Поделиться
Скачать
Advantech PCL-858 Скачать руководство пользователя страница 19

2 0

PCL-858   User's Manual

Operating Environment Selection

Set jumper 3 (JP3) to correspond with your desired software operating
environment. Connect the left two pins of JP3 to operate in DOS or
Windows 3.1 mode, as shown below. Connect the right two pins to
operate in Windows 95 or Windows NT mode .

JP3

  JP3

DOS, Windows 3.1

Windows 95, Windows NT

Icom Utility Setup for Windows 95/98/NT

environment

In this part, utility installation, configuration and upgrade/ removal
procedure are described. IOCM Utility software package is stated for
both Windows 95/98 and NT environments.

.

Utility Installation

The following is the procedure for installing PCL-858 under Windows
95/NT:

1.  Run Setup.exe in the driver diskette.

2.  Select “Advantech Icom Utility” to install and configure the
boards following the on-line instructions.

3.  When Advantech Icom Utility Configuration Panel is popped up,
please refer to the software for more detail.

4.  After this, user complete the whole installation, and restart Win-
dows 95.

1

1

Содержание PCL-858
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды