Advantech PCL-746+ Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 41

background image

Chapter 2 Hardware Installation 11

Default Settings

The board will be shipped in the RS-232 mode (Enhanced), all the
jumpers on the 12*3 pin jumper will be set to the upper position, this is
the cards default setting. The PCL-746+ DIP switch and jumper default
settings are as shown below:

PCL-746+ Default Configuration

Jumper

Default Function

Port1

RS-232

Port2

RS-232

Port3

RS-232

Port4

RS-232

JP4

IRQ12

S1

Address 300H

S5

Interrupt register 280H

Protocol Selection

Firstly you have to decide which mode each port will be operating in,
RS-232, RS-422 or RS-485. You can configure each port to operate in a
different mode if required. Each port has to be individually setup by
selecting the correct jumper configurations on two jumper groups, one
pair for each port. These consist of a 12*3 pin jumper (RS-232) and a
1*3 pin jumper (RS-422/RS-485).

Note: The second (RS-422/RS-485) jumper group is ineffective

when the main jumper group is configured to operate in
the RS-232 mode.

RS-232 or RS-422/RS-485 Mode Selection

Should you wish to configure the PCL-746+ to operate in the RS-232
mode, then the upper two pins of the 12*3 pin jumper should be
connected. For RS-422/ RS-485 mode selection, the bottom two pins of
the 12*3 pin jumper should be connected as shown below.

«
...
12
13
14
15
16
...
»

Содержание PCL-746+










































Отзывы:

Нет отзывов

Похожие инструкции для PCL-746+

Бренд: M-Audio Страницы: 10

Бренд: 3xLogic Страницы: 2

Бренд: National Instruments Страницы: 11

Бренд: Supero Страницы: 68

PARTNER Voice Messaging PC Card Release 2

Бренд: Lucent Technologies Страницы: 67

Бренд: Klark Teknik Страницы: 50

Бренд: ROE Страницы: 41

Бренд: MC Страницы: 21

Бренд: axing Страницы: 52

Бренд: AOpen Страницы: 18

Бренд: Rockwell Automation Страницы: 21

netHOST NHST-T100

Бренд: hilscher Страницы: 75

Бренд: Z-Wave Страницы: 42

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Smacq Technologies Страницы: 22

Protection Board R0E330850ACBP0

Бренд: Renesas Страницы: 8

Бренд: ELSA Страницы: 60

Бренд: Helmholz Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды