Advantech ICR-4453 Скачать руководство пользователя страница 21

Страница: 21 / 52

ICR-4453

2.2

Antennas Interfaces

SMA connectors

ANT0

ANT1

ANT2

and

ANT3

are intended to be used for connection

of the cellular antennas to the router. The GNSS antenna can be connected to the

GNSS

SMA connector. Three R-SMA connectors

WIFI1

are designed for the connection of the WiFi

antennas.

Do not run the router without connected cellular antennas as the energy from the trans-
mission is effectively reflected by the open end and can damage the equipment.

Recommended tightening moment for screwing the antenna to the SMA connector is 0.9 Nm.

2.3

Ethernet Interfaces

The RJ45 panel socket is used for four ETH0 (switched) and one ETH1 Ethernet interfaces.

The pinout of the socket is shown in Figure

and described in Table

Figure 6: Ethernet Connector Pinout of RJ45 Socket

Signal mark

Description

BI_DA+

Bi-directional pair A +

BI_DA-

Bi-directional pair A -

BI_DB+

Bi-directional pair B +

BI_DC+

Bi-directional pair C +

BI_DC-

Bi-directional pair C -

BI_DB-

Bi-directional pair B -

BI_DD+

Bi-directional pair D +

BI_DD-

Bi-directional pair D -

Table 2: Ethernet Connector Pinout Description of RJ45 Socket

All four ETH0 ports can be used for PoE PSE, if the router is equipped with this feature. For
technical parameters of PoE see Chapter

4.8

The isolation barrier of the Ethernet ports against the ground is 1500 V.

Содержание ICR-4453





















































Результаты поиска

Содержание ICR-4453

Отзывы:

Похожие инструкции для ICR-4453

Бренды по названию

Популярные бренды

Advantech ICR-4453, Руководство пользователя

Результаты поиска

Содержание ICR-4453

Отзывы:

Похожие инструкции для ICR-4453

Бренды по названию

Популярные бренды