Advantech ICR-4434 Скачать руководство пользователя страница 8

Страница: 8 / 52

ICR-4434

1. Product Overview

1.1

Product Introduction

The ICR-4434 is

LTE Advanced Cat 12

Router &

Powerful Edge Computing Gateway

focused on the global market.

Thanks to the ultra high-speed of data transfer, up to

600 Mbps for download

and

150

Mbps for upload

, is this router an ideal solution for demanding IoT applications such as

industrial routers and gateways, digital signage, industrial computers, and tablets, etc.

Two antennas, the main

ANT

and the diversity

DIV

, are intended for the cellular network.

An antenna for

GNSS

can be connected to the router. The router, assembled in a robust metal

box, is equipped with five

1Gb Ethernet ports

, one

SFP cage

together with interfaces of

RS232

RS485

CAN bus

, two

binary inputs

and two

binary outputs

. To backup the cellular

connection, the router offers two

SIM card readers

on the rear side of the router under the

SIM cover. A

microSD card

can be inserted under this cover as well. The designated router

models can be equipped with a

WiFi module

with

3x3 MIMO

antennas.

Configuration of the router may be done via a password-protected Web interface. Web in-

terface provides detailed statistics about the router’s activities, signal strength, detailed system
log etc. The router supports VPN tunnels using

IPSec

(),

OpenVPN

GRE

L2TP

PPTP

make sure safe communication.

IPv6 Dual Stack

DHCP

NAT

NAT-T

DynDNS

DNS proxy

VLAN

QoS

NTP

VRRP

, control by

SMS

, port forwarding, primary connection backup and

many other functions are supported.

The router provides

diagnostic functions

, which include automatically monitoring the

PPP connection, automatic restart in case of connection losses,

Low Power Mode

and

hard-

ware watchdog

that monitors the router status.

The user may insert

Linux scripts

which are started on various actions. It is possible to

create up to four different configurations for the same router. These configurations can be
switched when necessary via Web interface, SMS or binary input status.

The router can automatically upgrade its configuration and firmware from your central

server.

WebAccess/DMP

and

WebAccess/VPN

remote device management platforms are

supported as well.

Examples of possible applications

• mobile office

• fleet management

• security system

• telematic

• telemetric

• remote monitoring

• vending and dispatcher machines

Содержание ICR-4434





















































Результаты поиска

Содержание ICR-4434

Отзывы:

Похожие инструкции для ICR-4434

Бренды по названию

Популярные бренды

Advantech ICR-4434, Руководство пользователя

Результаты поиска

Содержание ICR-4434

Отзывы:

Похожие инструкции для ICR-4434

Бренды по названию

Популярные бренды