Advantech EKI-1526/N/I/TI Скачать руководство пользователя страница 33

Страница: 33 / 107

EKI-1526(TI) | 1528(TI) User Manual

2.2.3

Power Connection

Warning!

Power down and disconnect the power cord before servicing or wiring
the serial device server.

Warning!

Do not disconnect modules or cabling unless the power is first switched
off.

The device only supports the voltage outlined in the type plate. Do not
use any other power components except those specifically designated
for the serial device server.

Warning!

Disconnect the power cord before installation or cable wiring.

Warning!

Risk of explosion if the battery is removed and/or replaced by an
incorrect type.

Attention!

Risque d'explosion si la batterie est retirée et/ou remplacée par un
type incorrect.

Warning!

Risk of defeating the safeguard if the battery is removed or replaced by
an incorrect type.

Attention!

Risque de défaire la protection si la batterie est retirée ou remplacée
par un type incorrect.

Warning!

Risk of explosion if the battery is disposed in fire or hot environment or
mechanically damaged--denting, crushing, and piercing the cell case.

Содержание EKI-1526/N/I/TI












































































































Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Бренды по названию

Популярные бренды

Advantech EKI-1526/N/I/TI, Руководство пользователя

Результаты поиска

Содержание EKI-1526/N/I/TI

Отзывы:

Бренды по названию

Популярные бренды