Advantech EKI-1242 Series Скачать руководство пользователя страница 31

Страница: 31 / 64

EKI-1242 Series User Manual

2.4

Connecting the Fieldbus Gateway to Ethernet
Ports

2.4.1

RJ45 Ethernet Cable Wiring

For RJ45 connectors, data-quality, twisted pair cabling (rated CAT5 or better) is

recommended. The connector bodies on the RJ45 Ethernet ports are metallic and

connected to the GND terminal. For best performance, use shielded cabling.

Shielded cabling may be used to provide further protection.

Figure 2.7 Ethernet Plug & Connector Pin Position

Maximum cable length: 100 meters (328 ft.) for 10/100BaseT.

2.5

Serial Connection

EKI-1242 Series provides eight ports DB9 (male) connectors. RS-232/422/485 pin

assignments as below:

Figure 2.8 DB 9 Pin Position

Straight-thru Cable Wiring

Cross-over Cable Wiring

Pin 1

Pin 3

Pin 2

Pin 6

Pin 3

Pin 1

Pin 6

Pin 2

Pin

RS-232

DCD

DTR

GND

DSR

RTS

CTS

RS-422

TX-

TX+

GND

RX+

RX-

RS-485

DATA-

DATA+

GND

Содержание EKI-1242 Series

































































Результаты поиска

Содержание EKI-1242 Series

Отзывы:

Похожие инструкции для EKI-1242 Series

Бренды по названию

Популярные бренды

Advantech EKI-1242 Series, Руководство пользователя

Результаты поиска

Содержание EKI-1242 Series

Отзывы:

Похожие инструкции для EKI-1242 Series

Бренды по названию

Популярные бренды