Advantech AIMB-250F-00B1 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 105

background image

User’s Manual

AIMB-250 User’s Manual

83

3.5.11

Set Supervisor / User Password

You can set either supervisor or user password, or both of them.
Supervisor Password: able to enter/change the options of setup menus.

User Password: able to enter but no right to change the options of setup menus.

Type the password, up to eight characters in length, and press <Enter>. The password
typed now will clear any previously entered password from CMOS memory. You will be
asked to confirm the password. Type the password again and press <Enter>. You may also
press <Esc> to abort the selection and not enter a password. To disable a password, just
press <Enter> when you are prompted to enter the password. A message will confirm the
password will be disabled. Once the password is disabled, the system will boot and you can
enter Setup freely.

«
...
81
82
83
84
85
...
»

Содержание AIMB-250F-00B1










































































































Отзывы:

Нет отзывов

Похожие инструкции для AIMB-250F-00B1

Бренд: A-Trend Страницы: 40

Бренд: QDI Страницы: 69

Бренд: Zapi Страницы: 50

Бренд: ASROCK Страницы: 5

Бренд: Texas Instruments Страницы: 9

Бренд: MATSONIC Страницы: 77

BrillianX 1S/2000

Бренд: QDI Страницы: 63

Бренд: Intel Страницы: 36

Бренд: Supero Страницы: 143

Бренд: Pentium Страницы: 48

Бренд: ComNav Technology Страницы: 28

Бренд: Xilinx Страницы: 40

Бренд: Award Страницы: 60

Бренд: ASROCK Страницы: 57

Бренд: DFI Страницы: 61

Бренд: DFI Страницы: 75

Бренд: Gigabyte Страницы: 40

Бренд: Brother Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды