Advanced Thermoelectric ElectraCOOL L-A 550 Скачать руководство пользователя страница 17

Страница: 17 / 28

ElectraCOOL

LA550 Chiller

For Information Call

1 800-250-2920

electracool.com

One Tara Boulevard

Nashua, NH 03062 USA

international Inquiries (603) 888-2467

rev 7/03

Now set the controller input parameters as follows:

P1 HEAT = 2*P if system was heating in step 2.

P1 HEAT = 4*P if system was cooling in step 2.

I1 HEAT = 1.2*t

D1 HEAT = t/8

P2 COOL = P if system was heating in step 2.

P2 COOL = 2*P if system was cooling in step 2.

I2 COOL = 1.2*t

D2 COOL = t/8

6.0 System Alarms/Troubleshooting

The

ElectraCOOL

LA 550 Chiller has four system alarms that when triggered will

show on the display. When an alarm is displayed the system will not attempt

to heat or cool the coolant and the RED status light will illuminate. The P&ID is

included at the end of this section for your reference.

Tank Level Low:

Liquid reservoir level is too low. This is a warning only

and will not trigger the system failure alarm. It will illuminate the

RED status light.

Unless filling for the first time, check all

outside plumbing lines for leaks. Once all leaks are sealed, follow

the procedure in section 4.2 and add more coolant until the alarm

disappears.

Warning! Always disconnect the DC power cord before

opening the

ElectraCOOL

LA 550 Chiller cover as electrical

shock hazards exist inside.

RTD Open The temperature sensor has failed or its connector has come

loose.

/Shorted:

Turn off the ElectraCOOL LA 550 Chiller and disconnect the DC

power cord. Open the controller panel and check that the 5-pin

connector is firmly attached to the controller board and there are

no loose wires in the white miniature RTD connector located

inside. If both are correct, replace the internal RTD as per the

procedure in section 7.5.

Fan Fail:

Fan is supplying insufficient air to cool the thermoelectrics.

Either

one or both of the fans have failed or the airflow into or out of

the system is blocked. Check that the front and rear air inlet and

outlet gratings are not blocked. The ElectraCOOL LA 550 Chiller

requires at least 6 inches of clearance around these gratings. If

airflow is not blocked, contact ADVANCED THERMOELECTRIC for

an RMA number to return the unit for fan replacement.

Содержание ElectraCOOL L-A 550





























Результаты поиска

Содержание ElectraCOOL L-A 550

Отзывы:

Бренды по названию

Популярные бренды

Advanced Thermoelectric ElectraCOOL L-A 550, Руководство пользователя

Результаты поиска

Содержание ElectraCOOL L-A 550

Отзывы:

Бренды по названию

Популярные бренды