manualshive.com logo in svg

advanced scale models A-26 invader, Руководство по сборке, Страница: 2 / 24

Поделиться
Скачать
advanced scale models A-26 invader Скачать руководство пользователя страница 2

Page 2

cuSTomER SERvicE inFoRmATion

In the USA

Global Services

18480 Bandilier Circle

Fountain Valley, CA  92708

Phone: (714) 963-0329

Fax: (714) 964-6236

Email: [email protected]

In the EU

Ripmax Ltd.

241 Green Street

Enfield, EN3 7SJ, U.K.

Phone: +44(0) 20 8282 7500

Fax: +44(0) 20 8282 7501

Email: [email protected]

In Australia

Model Engines (Aust.) PTY. LTD.

P.O. Box 828, Noble Park, VIC., 3174

www.modelengines.com.au

SAFETY WARninGS

ThIS R/C MODEL IS DESIGNED FOR ExPERIENCED PILOTS ONLY! IF YOU ARE NOT AN ExPERIENCED PILOT 
COMFORTABLE wITh FLYING hIGh-PERFORMANCE MODEL AIRCRAFT, DO NOT CONTINUE.

LiKE thiS r/c modEL, thESE iNStrUctioNS arE WrittEN With thE ExpEriENcEd modELEr iN miNd. 
aLL maJor StEpS arE oUtLiNEd; hoWEvEr, thE iNStrUctioNS arE WrittEN KEEpiNg iN miNd that 
YOU'RE  ExPERIENCED  IN  BASIC  MODEL  ASSEMBLY  TEChNIqUES  AND  AIRCRAFT  SETUP.  IF  YOU  hAVE 
qUESTIONS DURING ASSEMBLY, PLEASE CONTACT YOUR LOCAL DISTRIBUTOR USING ThE CUSTOMER 
SERVICE INFORMATION ABOVE.

This R/c aircraft is not a toy! if misused or abused, it can cause serious bodily injury and/or damage to property. Fly only in open areas 

and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your aircraft before its first 
flight. Please carefully read and follow all instructions included with this aircraft, your radio control system and any other components 

purchased separately.

AddiTionAL iTEmS REQuiREd To compLETE ASSEmBLY

l

   x  5~6 Channel or More Radio Control System

l

  2 x   .52~.70 4-Stroke Engines and 2 x 6" or 3 x 6" Propellers

l

  7 x  High-Torque, Standard Servos for Ailerons, Flaps, Elevators and Rudder/Steering

l

  2 x  Standard Servos for Throttles

l

  4 x  2" Servo Extension Leads for Flaps and Throttles

l

  2 x  24" Servo Extension Leads for Ailerons

l

  1 x  Y-Harness with Electronic Reverser for Elevators

l

  3 x  Y-Harnesses (Standard) for Ailerons, Flaps and Throttles

l

  1 x  5 Cell 1100mAH or Greater Capacity Receiver Battery

l

  2 x  Remote Fueling Valves

l

  Five and Thirty Minute Epoxy

l

  Thin and Thick C/A

l

  C/A Debonder and Rubbing Alcohol

l

  Assorted Modeling Tools (i.e., Modeling Knife, Screwdriver, Hex Wrenches, Etc.)

l

  Assorted Modeling Supplies (i.e., Sandpaper, Sanding Block, Aircraft Stand, Paper Towels, Etc.)

optional phneumatic Retract installation

l

   x  ASM Retract Set and Control System for A-26 Invader (P/N ASM-ARS05)

l

   x  ASM Landing Gear Strut Set for A-26 Invader (P/N ASM-AVSS05)

l 

 x  Standard Servo for Retract Air Control Valve

Because of the number of servos and servo extension leads used, we strongly suggest the use 

of a 5 cell (6 Volt) 1100mAH or greater capacity receiver battery.

As an alternative to purchasing multiple servo extension leads, you may want to purchase a bulk 
spool of servo wire and connectors and make your own custom-length extension leads.

For more information about using an electric power system, including the brushless motors, ESCs, LiPO batteries, and 
the necessary steps for installation, please refer to the Brushless Power System Installation section on page 20.

Содержание A-26 invader

























Отзывы:

Нет отзывов