manualshive.com logo in svg

Advanced Motion Controls 12A8, Руководство по установке оборудования, Страница: 10 / 59

Поделиться
Скачать
Advanced Motion Controls 12A8 Скачать руководство пользователя страница 10

Keep clear of all exposed power terminals (motor, DC Bus, shunt, DC 

power, transformer) when power is applied to the equipment. Follow 

these safety guidelines: 

•

Always turn off the main power and allow sufficient time for 

complete discharge before making any connections to the drive. 

•

Do not rotate the motor shaft without power. The motor acts as a 

generator and will charge up the power supply capacitors through 

the drive. Excessive speeds may cause over-voltage breakdown in 

the power output stage. Note that a drive having an internal power 

converter that operates from the high voltage supply will become 

operative. 

•

Do not short the motor leads at high motor speeds. When the motor is 

shorted, its own generated voltage may produce a current flow as 

high as 10 times the drive current. The short itself may not damage 

the drive but may damage the motor. If the connection arcs or 

opens while the motor is spinning rapidly, this high voltage pulse flows 

back into the drive (due to stored energy in the motor inductance) 

and may damage the drive.

•

Do not make any connections to any internal circuitry. Only 

connections to designated connectors are allowed. 

•

Do not make any connections to the drive while power is applied.

MNALAZIN-02

2

Safety / General Safety Overview

Do not reverse the power supply leads!
Severe damage will result!

Use sufficient capacitance!
Pulse Width Modulation (PWM) drives require a capacitor on the high 

voltage supply to store energy during the PWM switching process. 

Insufficient power supply capacitance causes problems particularly with 

high inductance motors. During braking much of the stored mechanical 

energy is fed back into the power supply and charges its output 

capacitor to a higher voltage. If the charge reaches the drive’s over-

voltage shutdown point, output current and braking will cease. At that 

time energy stored in the motor inductance continues to flow through 

diodes in the drive to further charge the power supply capacitance. The 

voltage rise depends upon the power supply capacitance, motor 

speed, and inductance.
A 2

μ

H motor at 20 amps can charge a 2000 

μ

F capacitor an additional 

30 VDC. An appropriate capacitance is typically 2000 

μ

F/A maximum 

output current for a 50 VDC supply.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 12A8




























































Отзывы:

Нет отзывов