AQS-CDT1-D
Config Bandwidth Modulation FEC Guard
Video (per Default)
Audio
Data Input
Data Rate
1
8 MHz
QPSK
1/2
1/4
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
2
8 MHz
QPSK
2/3
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
3
8 MHz
QPSK
5/6
1/16
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
4
8 MHz
16QAM
2/3
1/4
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
5
8 MHz
16QAM
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
6
8 MHz
16QAM
5/6
1/16
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
7
8 MHz
64QAM
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
8
8 MHz
64QAM
7/8
1/16
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
Config Bandwidth Modulation FEC Guard
Video (per Default)
Audio
Data Input
Data Rate
1
2.5 MHz
QPSK
1/3
1/8
NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms
9600
2
2.5 MHz
QPSK
1/3
1/16
NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms
9600
3
2.5 MHz
QPSK
2/3
1/8
NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms
9600
4
2.5 MHz
QPSK
2/3
1/16
NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms
9600
5
2.5 MHz
16QAM
2/3
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
6
8 MHz
QPSK
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
7
8 MHz
16QAM
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
8
8 MHz
64QAM
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
Config Bandwidth Modulation FEC Guard
Video (per Default)
Audio
Data Input
Data Rate
1
1.25 MHz
QPSK
1/3
1/8 NTSC (15 fps) or PAL (12.5 fps) 8 kHz, 16-Bit, Stereo Same as Comms
9600
2
1.25 MHz
QPSK
2/3
1/16
NTSC (30 fps) or PAL (25 fps) 8 kHz, 16-Bit, Stereo Same as Comms
9600
3
2.5 MHz
QPSK
1/3
1/8
NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms
9600
4
2.5 MHz
QPSK
2/3
1/8
NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms
9600
5
2.5 MHz
16QAM
1/3
1/8
NTSC (30 fps) or PAL (25 fps) 16 kHz, 16-Bit, Stereo Same as Comms
9600
6
8 MHz
QPSK
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
7
8 MHz
16QAM
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
8
8 MHz
64QAM
3/4
1/8
NTSC (30 fps) or PAL (25 fps) 32 kHz, 16-Bit, Stereo Same as Comms
9600
6/7/8 DVB-T Bandwidth
Narrowband Bandwidth
Ultra-Narrowband Bandwidth
How to Set Your Transmitter Configuration
The CDT1 Transmitter has two modes for configuring the unit: Local Mode and Remote Mode . Local Mode
utilizes 5 buttons for configuration settings and frequency selection. To change the frequency or configuration
preset, press the enter button then select the digit you want to change by using the left/right
buttons the digit will flash when selected. Use the up/down arrows to change the selected digit.
When you are done press the enter button to save and activate the settings.
The CONFIG allows you to select one of 8 configuration presets as
shown in the tables below. The CDT1 can only be programmed
when it is set to configuration “0” which is programming mode.
“PROG” is displayed on the 4, seven segment displays to the left
when in programming mode.
Line/Mic (“-10d” /”-55d”) are selectable when CONFIG is set to “L”,
RS232/TTL (“232”/”3.3”) are selectable when CONFIG is set to “d”
and Power level 1mW to 100 mW (“0”-“20”) is selectable when
CONFIG is set to “P” (for variable power transmitters).
Wiring Your CDT1 Transmitter
(Audio/Data Connections are Dependent on Configuration )
SSMA Female
Video Input
(Connect to Camera)
SMA Female
RF Output
(Connect to Antenna)
MDM-9P
Power & Programming
1:
2:
3:
4:
5:
6:
7:
8:
9:
+11 to 16 VDC Input
Ground
Ground
Ground
12 VDC Out
NC/TX Comm-
TX Comm+
RX Comm+
NC/RX Comm-
MDM-9S
Audio/Data Input
1:
2:
3:
4:
5:
6:
7:
8:
9:
Audio 1 Mic
Audio 1 Line
Ground
Audio 2 Mic
Audio 2 Line
Ground
TTL Data
RS232 Data
Ground
1
5
6
9
1
5
6
9
NC = No Connection
