background image

Document Number: QIG-00001-A 
P/N: NONE   

 

 

Q

Q

u

u

i

i

c

c

k

k

 

 

I

I

n

n

s

s

t

t

a

a

l

l

l

l

a

a

t

t

i

i

o

o

n

n

 

 

G

G

u

u

i

i

d

d

e

e

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copyright Notice 

All title, copyright and other intellectual property rights in and to the Software Product(Including but not 

limited to any relevant media, images, photographs, animations, video, audio, text, and applets 

incorporated into the Software Product),the accompanying manuals and other documents, and on-line 

or electronic documents, if any,(collectively “Software Product”) are owned by the Manufacturer unless 

otherwise expressly licensed by The Manufacturer in writing, any provision of the Software Product 

does not represent any license of any of the above rights. 

 

Trademark notice 

The Manufacturer and other names of The Manufacturer products are trademarks or registered 

trademark of The Manufacturer. 

                                     

Revisions 

The Manufacturer reserves the right to revise this publication and to make changes in the content 

hereof without the obligation of The Manufacturer to notify any person of such revision or changes. 

Содержание RMC-2QD-2


















Отзывы: