background image

15

4. 

Away from water. 

Protect from exposure to water, including water sprayed from 

nozzles. In a wall-mounted configuration, mount the batteries at least 50 mm (2 
in) off the ground.

5. 

Orientation. 

Install the battery in any direction other than face down. Do not 

install face-down.

6. 

Indoor or outdoor.

 Suitable for use indoors. Refer to 

Section 3.3, Environmental 

Specifications

 for temperature ranges in which the battery can operate.

NOTE

•  Using this product in a location that does not meet requirements will void the 

warranty.

9.3  DC Cables

 CAUTION

FIRE HAZARD

•  Undersized cables can become hot and may potentially catch fire.

Failure to follow these instructions can result in minor to moderate injury.

The DC battery cables should meet the following requirements:
1. 

Copper-stranded cable. 

DC cables must be stranded, copper, and rated 90 °C 

minimum. Terminate the cables with lugs that fit the DC terminals.

2. 

Minimum cable lengths. 

Select a location that minimizes the length of 

battery cables to reduce voltage drop from the impedance leading to reduced 
performance.

3. 

Appropriate

 

cable

 

gauge. 

The cables should be capable of carrying the normally 

expected current, plus a margin of safety.

4. 

Proper

 

polarity. 

Positive (+) is connected to positive (+), and negative (-) is 

connected to negative (-).

5. 

Minimum cable lengths

. Select a location that minimizes the length of 

battery cables to reduce voltage drop from the impedance leading to reduced 
performance.

9.4  Protection

 CAUTION

FIRE

 

HAZARD

•  Undersized fuses and disconnects may become overloaded and potentially cause a 

fire.

•  Fuses and disconnects are required to open before the cable reaches its maximum 

current carrying capability.

Failure

 

to

 

follow

 

these

 

instructions

 

can

 

result

 

in

 

minor

 

to

 

moderate

 

injury.

Additional DC overcurrent protection and a DC disconnect switch are required to 
protect the system and DC battery cables.

Содержание Discover 42-48-6650





























Отзывы: