ADTRAN TRACER 2xE1 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 62

background image

TRACER 2 x E1 User’s Manual

61280004L2-1C

Section 2 Installation

11

UNPACK, INSPECT

Carefully inspect the TRACER for any shipping damages. If damage is suspected, file a claim
immediately with the carrier then contact ADTRAN Customer Service. If possible, keep the original
shipping container for use in shipping the TRACER back for repair or for verification of damage during
shipment.

Before beginning installation, verify that all of the following components are present.

Rackmounted RFC Configuration:

Provided by ADTRAN • Baseband Processor (BBP)

• Rackmounted RF Converter (RFC)
• BBP to RFC IF interconnect cable

Provided by customer

• E1 Interface cables
• Antenna feedline cable
• Antenna and mounting hardware
• VT100 terminal and RS-232 interface cable (optional)
• 21 to 60 volt DC power source (available from ADTRAN), either
polarity referenced to ground

Mastmounted RFC Configuration:

Provided by ADTRAN • Baseband Processor

• Mastmounted RF Converter

Provided by customer

• E1 interface cables
• Antenna feedline cable
• Antenna and mounting hardware
• BBP to mastmounted RFC IF interconnect cable
• VT100 terminal and RS-232 interface cable (optional)
• 21 to 60 volt DC power source (available from ADTRAN), either

polarity referenced to ground

INSTALLATION

Location and Mounting

Install the TRACER in a location that requires minimal antenna feedline length (the loss in this cable
directly affects overall system performance). When used with a rackmount RFC the BBP is designed to
be mounted above the RFC. Although no space is needed between the units, certain regulations may
require at least 19.05 mm (.75") of space above and below the BBP.

Power Requirements

The TRACER can operate from a supply between 21 and 60 volts DC, with either polarity referenced to
ground, and consumes 30 watts. Amperage is determined by dividing the wattage (30) by the input
voltage (i.e., 30 watts/48 volts = .625 amps).

11

S

ECTION

2

I

NSTALLATION

«
...
19
20
21
22
23
...
»

Содержание TRACER 2xE1































































Отзывы:

Нет отзывов

Похожие инструкции для TRACER 2xE1

Бренд: 3Com Страницы: 20

Бренд: D-Link Страницы: 15

DSN-4100 Series

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

Бренд: Habitat Страницы: 48

Бренд: M2M Страницы: 9

Бренд: Salto Страницы: 2

Бренд: A10 Страницы: 52

Бренд: Genie Страницы: 15

Бренд: WaiLan Страницы: 27

APS6-400 Series

Бренд: Eaton Страницы: 114

Бренд: Sangamo Страницы: 2

Бренд: Magnadyne Страницы: 8

Бренд: BEC Страницы: 159

Бренд: MSNswitch Страницы: 2

Bolide BN-NVR/NX

Бренд: GSA Страницы: 101

Бренд: Cradlepoint Страницы: 2

Бренд: RadioSPECTRAL Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды