PRICING AND AVAILABILITY 800.827.0807
TECH SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61179611L3-22A
TOTAL ACCESS 1200 IP NETWORK MODULE
PROVISIONING
The Total Access 1200 has a front panel mounted DB-9 connector that supplies an RS-232 interface for
connection to a controlling terminal. The supported terminal type is VT100 or compatible and is set
for 9600 baud, 8 data bits, no parity, and 1 stop bit.
At the Total Access 1200 Login Screen, enter the account name and password. Note that the default
login is “ADMIN” and the password is “PASSWORD” and can be changed upon initial login. The login
and password are case sensitive.
NOTE:
To traverse through the menus, select the desired entry and press Enter. To work backward in the
menus, press the Escape key.
PROVISIONING OPTIONS
Upon initial installation, the IP Network Module will be provisioned according to factory default
settings as shown in the table below.
Provisioning Option
Available Options
Default Setting
Bridge Circuit Management
Each user must have a Bridge Port set up for proper operation.
The VPI, VCI, and Encapsulation settings will be determined by the ADSL modem being used by the customer
VPI
0-40960
VCI
32-65536
35
Encapsulation
LLC Bridged; VC MUX
LLC Bridged
Enabled/Disabled (service state)
Enabled; Disabled
Enabled
Ethernet Provisioning
Duplex Mode
Auto Negotiate; Full Duplex; Half Duplex
Auto Negotiate
Speed
Auto Negotiate; 100Base; 10Base
Auto Negotiate
System Management
IP Address, Mode
Static; Dynamic (BOOTP/DHCP)
Dynamic
Password Control, Auto Logout
Disabled; Enabled
Disabled
Allow SNMP Security Management
Disabled; Enabled
Disabled
Baud Rate
9600; 19200; 38400
9600
The portions of the menu tree required to configure the IP Network Module are shown to the right.
Use these sections to perform the provisioning steps for the IP Network Module. The default values
are indicated by an asterisk.
1. Configuration
Unit Name
CLEI Code
Part Number
Product Revision
Serial Number
Software Revision
1. IP
Address
2. Subnet Mask
3. Default Gateway
5. Reset IP
Factory Defaults
4. TFTP
Address
1. TFTP
Address
5. Reset IP
Factory Defaults
1. Port
2. Previous 15 Minute Periods
3. Clear Previous PM Counts
1. IP
Address
2. V
e
rsion
1. Auto
Negotiate*
2. Full Duplex
3. Half Duplex
4. Auto
Negotiate*
5. 100Base
6. 10Base
1. Contact Information
2. Community Names
3. T
rap
Hosts
4.
T
raps Enabled (Y
es*/No)
1. Set Passwords
2.
Auto Logout (Disabled)*
3.
Allow SNMP
Security Management (Disabled)*
LLC Bridged*
VC Mux
1. Duplex Mode
2. Speed
1. Current
2. Previous
1. Mode
2. Configure
1. Static
2. Dynamic (BOOTP/DHCP)
(Dynamic)
(Static)
4. Restore Default Passwords
1. Y
-MODEM
2. TFTP
1. 9600*
2. 19200
3. 38400
2. Bridge Circuit Management
1. Bridge User Port Provisioning
2. Ethernet Provisioning
3. Ethernet Statistics
4. User Port Statistics
1. Adjust
T
ime
2. Adjust
Date
3. System
Management
2. Password Control
1. IP
Address
3. T
ime/Date
4. Baud Rate
6. Download New Code
7. Restore Factory Defaults
5. SNMP
1. Port (1-24)
2. Circuit ID (T
ext)
3. VPI (0-4096)*
4. VCI (32-65536) 35*
(T
oggle)
7. Save Changes
8. V
iew
All Ports
9.
Apply Provisioning to Ports
5. Encapsulation
6. Enabled/Disabled*
1. Clear
Alarm Log
2. Next Page
4. User Ports
See I&M Practice for Chassis
5. System
Alarms
6. Contact Information
7. Logof
f
* Factory Default Settings
