NetVanta Dual T1/FT1 Network Interface Module (NIM)
P/N 1200872L1
For more detailed documentation, visit us online at
www.adtran.com
.
Quick Start Guide
®
Quick Start Guide, 61200872L1-13F, November 2006
Copyright © 2006 ADTRAN, All Rights Reserved
T1/FT1 NIM C
OMMANDS
clock source [internal | line* | through]
Configures the source timing used for the interface. Use the
no
form of this command to return
to the default value.
Note: the Dual T1 NIM supports a single clock source for both T1
interfaces. Changing the clock source on one T1 interface automatically affects the
configuration of the other T1 interface. For example, setting the clock source to
line
on the first
T1 configures the clock source of the second T1 as
through
.
internal
Configures the unit to provide clocking using the internal
oscillator.
line
*
Configures the unit to recover clocking from the T1 circuit.
through
Configures the unit to recover clocking from the circuit connected
to the alternate T1 interface.
coding [ami | b8zs*]
Configures the line coding for a T1 physical interface. This setting must match the line coding
supplied on the circuit by the service provider.
ami
Configures the line coding for alternate mark inversion (AMI).
b8zs
*
Configures the line coding for bipolar eight zero substitution
(B8ZS).
fdl [ansi* | att | none]
Configures the format for the facility data link (FDL) channel on the T1 circuit. FDL channels
are only available on point-to-point circuits. Use the
no
form of this command to return to the
default value.
ansi
*
Configures the FDL for ANSI T1.403 standard.
att
Configures the FDL for AT&T TR 54016 standard.
none
Disables FDL on this circuit.
framing [d4 | esf*]
Configures the framing format for the T1 interface. This parameter should match the framing
format supplied by your network provider. Use the
no
form of this command to return to the
default value.
d4
Specifies D4 superframe (SF) format.
esf
*
Specifies extended superframe (ESF) format.
lbo [long
<-22.5, -15, -7.5- 0>
| short
<0 to 655>
]
Configures the line build out (LBO) for the T1 interface. Use the
no
form of this command to
return to the default value.
long
<-22.5, -15, -7.5- 0>
Configures the LBO (in dB) for T1 interfaces with cable lengths
greater than 655 feet. Choices are -22.5, -15, -7.5, and 0 dB.
short
<0 to 655>
Configures the LBO (in feet) for T1 interfaces with cable lengths
less than 655 feet. Range is 0 to 655 feet.
loopback network [line | payload]
Initiates a loopback on the interface toward the network. Use the
no
form of this command to
deactivate the loopback.
line
Initiates a metallic loopback of the physical T1 network interface.
payload
Initiates a loopback of the T1 framer (CSU portion) of the T1
network interface.
loopback remote line [fdl | inband]
Sends a loopback code to the remote unit to initiate a line loopback. Use the
no
form of this
command to send a loopdown code to the remote unit to deactivate the loopback.
fdl
Uses the facility data link (FDL) to initiate a full 1.544 Mbps
physical (metallic) loopback of the signal received by the remote
unit from the network.
inband
Uses the inband channel to initiate a full 1.544 Mbps physical
physical (metallic) loopback of the signal received from the
network.
loopback remote payload
Sends a loopback code to the remote unit to initiate a payload loopback. A payload loopback
is a 1.536 Mbps loopback of the payload data received from the network maintaining bit-
sequence integrity for the information bits by synchronizing (regenerating) the timing. Use the
no
form of this command to send a loopdown code to the remote unit to deactivate the
loopback.
remote-alarm [rai]
Selects the alarm signaling type to be sent when a loss of frame is detected on the T1 receive
signal. Use the
no
form of this command to disable all transmitted alarms.
rai
Specifies sending a remote alarm indication (RAI) in response to a
loss of frame. Also prevents a received RAI from causing a change in
interface operational status.
remote-loopback
Configures the interface to respond to loopbacks initiated by a remote unit (or service
provider). Use the
no
form of this command to disable this feature.
snmp trap line-status
Controls the Simple Network Management Protocol (SNMP) variable
dsx1LineStatusChangeTrapEnable (RFC2495) to enable (or disable) the interface to send
SNMP traps when there is an interface status change. Use the
no
form of this command to
disable this trap.
snmp trap link-status
Controls the Simple Network Management Protocol (SNMP) variable
ifLinkUpDownTrapEnable (RFC2863) to enable (or disable) the interface to send SNMP traps
when there is an interface status change. Use the
no
form of this command to disable this
trap.
snmp trap threshold-reached
Controls the Simple Network Management Protocol (SNMP) variable
adGenAOSDs1ThresholdReached (adGenAOSDs1-Ext MIB) to enable the interface to send
SNMP traps when a DS1 performance counter threshold is reached. Use the
no
form of this
command to disable this trap.
tdm-group
<group number>
timeslots
<1-24>
speed 64
Creates a group of contiguous DS0s on this interface to be used during the cross-connect
process.
<group number>
Identifies the created TDM group (valid range: 1 to 255).
timeslots
<1-24>
Specifies the DS0s to be used in the TDM group. This can be entered
as a single number representing one of the 24 T1 channel timeslots or
as a contiguous group of DS0s. (For example,
1-10
specifies the first
10 channels of the T1.)
speed 64
Specifies the individual DS0 rate on the T1 interface to be 64 kbps.
This is the only supported speed on this module.
test-pattern [clear | errors | insert | ones | p215 | p220 | p511 | qrss | zeros]
Activates the built-in pattern generator and begins sending the specified test pattern. Can be
used to verify a data path when used in conjunction with an active loopback. Use the no form
of this command to cease pattern generation.
clear
Clears the test pattern error count.
errors
Displays the test pattern error count.
insert
Inserts an error into the currently active test pattern.
ones
Generates a test pattern of continuous ones.
p215
Generates a pseudorandom test pattern sequence based on a 15-bit
shift register.
p220
Generates a pseudorandom test pattern sequence based on a 20-bit
shift register.
p511
Generates a test pattern of repeating ones and zeros.
qrss
Generates a test pattern of random ones and zeros.
zeros
Generates a test pattern of continuous zeros.
* Indicates default values.
