background image

Quad Fiber Remote (QDFR) Unit Installation and Maintenance Practice

14

61181307L7-5E

BERT Test Screen

The Channel # BERT Test screen (

Figure 12

) performs a test with the following options:

• (Re)start Pattern – Use this option to (re)start a test.
• Stop Test – Use this option to manually stop a test.
• Select Data Pattern – Use this option to access the Current Pattern menu (

Figure 13

), which 

is used to select the appropriate data test pattern for the desired results.

Figure 12.  BERT Test Screen

Figure 13.  Network Pattern Screen

Shelf:  1  Slot:  2           Total Access System                 mm/dd/yy hh:mm
Unacknowledged Alarms:
                      CH 1 Circuit ID:
                            Channel 1 BERT Test Screen

                                  Test Results
              -----------------------------------------------------
                  Test Direction:              T1 Interface
                  Unframed Pattern Generation: OFF
                  Pattern:                     QRSS Pattern
                  Line Coding:                 AMI
                  Bit Errors:                  0000000
                  Bit Error Rate:              0.0E-0
                  Pattern Sync:                N/A
                  Pattern Sync Losses:         000
                  Test Length (HH:MM:SS):      01:00:00
                  Time Elapsed (HH:MM:SS):     00:00:00
              -----------------------------------------------------
              1.  (Re)start Pattern             2.  Stop Test
              3.  Select Data Pattern           4.  Enter Test Timeout
              5.  Toggle Test Direction

         'Sx'- Select Channel x 'N' - Next Channel  'P' - Previous Channel
                          Selection:

Shelf:  1  Slot:  2           Total Access System                 mm/dd/yy hh:mm
Unacknowledged Alarms: 

                           NETWORK Pattern Screen

                             Current Pattern = QRSS Pattern
                             ------------------------------------

                             1. 63 Pattern
                             2. 511 Pattern
                             3. 2047 Pattern
                             4. REV. 2047 Pattern
                             5. 2^15 Pattern
                             6. 2^20 Pattern
                             7. QRSS Pattern
                             8. 2^23 Pattern

                          Selection:

Содержание QDFR Unit

















































Отзывы: