2
Copyright © 2009 ADTRAN, Inc. All Rights Reserved.
Quick Start Guide, 64703863G1-13A, September 2009
3
G
ETTING
A
C
ELLULAR
A
CCOUNT
Before you attempt to connect to the 3G cellular network, make sure you have subscribed to an
appropriate CDMA service plan with your wireless service provider. The electronic serial number
(ESN) will be needed for this process. The ESN can be obtained by using the
show interface
cellular hardware
command at the command line interface (CLI) prompt. Refer to page 3 for
instructions on accessing the AOS CLI. The following is sample output of the
show interface
cellular hardware
command showing the ESN:
#show interface cellular 1/1 hardware
Electronic Serial Number (ESN): 0x12345678
Preferred Roaming List (PRL) Version: 12345
Mobile Directory Number (MDN): 0123456789
Mobile Station ID (MSID): 0123456789
System ID (SID): 1234
Network ID (NID): 12
G
ETTING
S
TARTED
Once you have subscribed to a CDMA service plan, you must activate the NetVanta 3G CDMA
NIM. Two activation and configuration methods are available for your NIM:
•
Web-based graphical user interface (GUI)
•
CLI
The GUI lets you configure the unit’s settings and provides online guidance and explanations for
each setting. However, using the AOS CLI may be necessary for more advanced configurations.
A
CCESS
THE
GUI
You can access the GUI from any Web browser on your network by following these steps:
1.
Connect the router to your PC using the Ethernet port on the front of the unit and an Ethernet
cross-over cable.
2.
During bootup, your PC will obtain an IP address from the NetVanta unit’s Dynamic Host
Configuration Protocol (DHCP) server. By default, the DHCP server is enabled
.
3.
Enter the unit’s IP address in your browser address line. The default IP address is
10.10.10.1
.
4.
You will then be prompted for the user name and password (the default settings are
admin
and
password
).
5.
The initial GUI screen appears.
A
CTIVATE
THE
3G CDMA NIM U
SING
THE
GUI
To activate the 3G CDMA NIM and cellular interface using the GUI, follow these steps:
1.
Select
Physical Interfaces
from the
System
menu.
2.
Select the
Cellular
interface to modify from the menu.
3.
Select
Activate
in the
Maintenance
dialogue box.
4.
When the activation call is in progress, the WWAN LED on the 3G NIM on the back of the 3G
router will be flashing constantly. When the activation call is complete, the WWAN LED will stop
flashing. At this point, the
Status
dialogue box will indicate if the activation call was successful.
A
CCESS
THE
CLI U
SING
THE
CONSOLE P
ORT
To establish a connection to the NetVanta router
CONSOLE
port, you need the following items:
•
VT100 terminal or PC (with VT100 terminal emulation software)
•
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end
1.
Connect the DB-9 (male) connector of your serial cable to the
CONSOLE
port on the rear panel of
the unit and connect the other end of the serial cable to the terminal or PC.
2.
Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press
<Enter>
to activate the AOS CLI.
3.
Enter
enable
at the
>
prompt.
4.
Enter the enable password when prompted. The default password is
password
.
A
CCESS
THE
CLI U
SING
A
T
ELNET
S
ESSION
To establish a connection to the NetVanta router using a Telnet session, you need the following
items:
•
VT100 terminal or PC (with VT100 terminal emulation software)
•
Ethernet cross-over cable
1.
Connect the router to your PC using the Ethernet port on the front of the unit and an Ethernet
cross-over cable.
2.
During bootup, your PC will obtain an IP address from the NetVanta unit’s DHCP server. By
default, the DHCP server is enabled
.
3.
Open a Telnet session by going to
Start > Run
and entering
telnet 10.10.10.1
.
4.
You will be prompted for a password. The default password is
password
.
5.
Enter
enable
at the
>
prompt.
6.
Enter the enable password when prompted. The default password is
password
.
A
CTIVATING
THE
3G CDMA NIM U
SING
THE
CLI
To activate the 3G CDMA NIM and cellular interface using the CLI, follow these steps:
1.
Enter
config terminal
at the
#
prompt.
2.
At the
(config)#
prompt, enter
interface cellular 1/1
to access the configuration parameters for
the cellular interface.
3.
At the
(config-cellular 1/1)#
prompt, enter
cdma activate [oma-dm | otasp]
. If you are
connecting to the Sprint network, use the
oma-dm
keyword. If you are connecting to the Verizon
network, use the
otasp
keyword.
4.
If the activation is successful, you will see the
Activation SUCCESSFUL
message in the
command output. If you see the
Activation FAILED
message, repeat activation Step 3 until you
are successful.
5.
Enter
exit
to exit the cellular interface commands and return to the Global Configuration mode.
