Quick Start Guide, 64703863G1-13A, September 2009
1
N
ET
V
ANTA
3200G 3G W
IRELESS
R
OUTER
P/N 4703863G1
4
Copyright © 2009 ADTRAN, Inc. All Rights Reserved.
A
NTENNA
I
NSTALLATION
I
NSTRUCTIONS
1.
Place either of the two antennas directly onto the antenna port labeled
ANT1
on the rear panel.
2.
Using the thumb screws only, carefully thread the antenna onto the connector until it is secure.
3.
Repeat Step 2 with the second antenna, attaching it to the
ANT2
port.
4.
Position antennas in a “V” shape at a 90 degree angle to each other.
3G CDMA NIM S
PECIFICATIONS
Wireless Technologies
1xRTT
1xEVDO Revision 0
1xEVDO Revision A
Frequency Bands
Band Class 0 (Cellular 800 MHz)
Band Class 1 (PCS 1.9 GHz)
Compliance
FCC Part 15, Class A
FCC Parts 2, 22, 24
UL/CUL 60950-1
RSS 102
IC ES-003
RSS 129/133
RSS 132/133
The 3G CDMA network interface module (NIM) device has been designed to operate with
the antennas listed below, and having a maximum gain of 2 dB. Antennas not included in
this list or having a gain greater than 2 dB are strictly prohibited for use with this device.
The required antenna impedance is 50 ohms.
Proper antennas are: Pulse/Larson Dipole Antenna, Part Number: SPDA24850/1900
To reduce potential radio interference to other users, the antenna type and its gain should
be chosen so that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
3G CDMA NIM LED D
ESCRIPTIONS
LED Label LED Color
Indication
WWAN
Off
3G modem is not powered.
Green (solid)
3G modem is powered, associated, and authenticated, but
not transmitting or receiving.
Green (slow flash)
3G modem is powered and searching, but not associated or
authenticated.
Green (intermittent flash)
3G modem activity is proportional to transmitting/receiving
speed (3 Hz minimum rate, 20 Hz maximum rate).
RSSI
(Received
Signal
Strength
Indication)
Off
No service or no signal detected.
Red (solid)
Low signal strength.
Amber (solid)
Medium signal strength.
Green (solid)
High signal strength.
1xRTT
Off
No 1xRTT service is available.
Green (solid)
1xRTT service is available.
EVDO
Off
No 1xEVDO service is available.
Green (solid)
1xEVDO service is available.
C
ONNECTING
TO
THE
C
ELLULAR
N
ETWORK
By default, your NetVanta 3200G 3G Wireless Router is shipped with DHCP, domain naming
system (DNS), and the demand interface enabled. This default configuration allows the user to
connect to the cellular network without any further configuration.
Once the 3G router is activated on the cellular network, ping a host device to test connectivity.
Connecting to the cellular network generally takes two ping cycles to complete. When the 3G
router has successfully connected, the demand interface should change its state to up.
C
ONFIGURE
Y
OUR
A
PPLICATION
For more detail on configuring your system, refer to the
AOS Command Reference Guide
(article
number 2219) and
Wireless Configuration Guide
(article number 2078) provided on the
AOS
Documentation
CD included in your shipment or available online at
http://kb.adtran.com
.
Important:
For additional details on product features, specifications, installation, and
safety, refer to the appropriate hardware installation guide on the
AOS Documentation
CD
shipped with the base unit and available online at
http://kb.adtran.com
.
