61700340F1-13D
3
2
61700340F1-13D
1. At the
#
prompt, enter
config terminal
.
2. At the
(config)#
prompt, enter
interface gigabit-eth 0/1
to access the configuration parameters for the
GIG 0/1
port.
3. Enter
ip address 10.10.10.1 255.255.255.0
to assign an IP address to the
GIG 0/1
port using a 24-bit
subnet mask.
4. Enter
no shutdown
to activate the interface to pass data.
5. Enter
exit
to exit the Ethernet interface commands and return to the Global Configuration mode.
6. Enter
ip route 0.0.0.0 0.0.0.0 10.10.10.254
to add a default route to the route table.
0.0.0.0
is the default
route and the default subnet mask, and
10.10.10.254
is the next-hop IP address to which the AOS router
should send all of its traffic. You will need to enter the proper route, subnet mask, and gateway for your
network. This information is typically provided by a service provider or local network administrator.
7. Enter
do write
to save the current configuration.
g
NOTE
The configuration parameters used in the examples outlined in this document are for instructional purposes
only. Please replace all underlined entries (
example
) with your specific parameters to configure your appli
-
cation.
C
HANGING
L
OGIN
P
ASSWORDS
U
SING
THE
CLI
To change the login passwords for the NetVanta 3140, connect to the CLI and follow these steps:
1. To modify the user accounts and passwords, from the
(config)#
prompt, enter the command
username
<username>
password
<password>
.
2. To modify the Enable mode password, from the
(config)#
prompt, enter the command
enable
password
<password>
.
3. To modify the Telnet password, from the
(config)#
prompt, enter the command
line telnet 0 4
and then
press ENTER. Enter the command
password
<password>
.
4. Enter
do write
to save the current configuration.
g
NOTE
On the 1700341F1, the behavior of the
LINK
and
ACT
LEDs (labeled
GIG 1
through
GIG 3
) on the front of the
unit corresponds to the behavior of the RJ-45 LEDs (labeled
GIG 0/1
through
GIG 0/3
) located on the back of
the unit.
F
RONT
P
ANEL
LED
S
LED
Color
Indication
STAT
Green (flashing)
The unit is powering up. On power-up, the
STAT
LED flashes rapidly
for five seconds.
Green (solid)
The power is on and self-test passed.
Red (solid)
The power is on, but the self-test failed or the boot mode (if
applicable) code could not be booted.
Amber (solid)
The unit is in bootstrap mode.
USB
Off
The interface is shut down or not connected.
Green (solid)
A supported device is connected.
Amber (flashing) There is activity on the link.
Red (solid)
An alarm condition is occurring on the USB port, or there is a failure.
LINK
(GIG 1 - GIG 3)
(1700340F1 only)
Off
The port is administratively disabled or does not have link.
Green (solid)
The port is enabled and the link is up.
ACT
(GIG 1 - GIG 3)
(1700340F1 only)
Off
There is no activity on the link.
Green (flashing)
There is activity on the link.
Port LEDs
(GIG
0/1 -
GIG 0/3)
Off
There is no activity on the link.
Green (solid)
The port is enabled and the link is up.
Amber (flashing) There is activity on the link.
A
CCESSING
THE
CLI
Access the AOS CLI via the
CONSOLE
port or a Telnet or SSH session. To establish a connection to the
NetVanta unit
CONSOLE
port, you need the following items:
■ PC with VT100 terminal emulation software.
■ Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for
your terminal or PC communication port on the other end.
g
NOTE
There are many terminal emulation applications available on the web. PuTTy, SecureCRT, and HyperTerminal
are a few examples.
1. Connect the DB-9 (male) connector of your serial cable to the unit’s
CONSOLE
port.
2. Connect the other end of the serial cable to the terminal or PC.
g
NOTE
Many PCs do not come with a standard serial port. A universal serial bus (USB) to serial adapter can be used
instead. The drivers for the USB to serial adapter must be installed according to the manufacturer’s instructions.
If the USB to serial adapter is not properly installed on your PC, you will not be able to communicate with the
AOS unit and you should seek support from the USB to serial adapter manufacturer.
3. Provide power to the unit as appropriate. Refer to the
NetVanta 3100 Series Hardware Installation Guide
available online at
https://supportcommunity.adtran.com
for more details.
4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8
data bits, no parity bits, 1 stop bit, and no flow control. Press
<Enter>
to activate the AOS CLI.
5. Enter
enable
at the
>
prompt and enter the Enable mode password when prompted. The default
password is
password
.
You can also access the CLI from a Telnet or SSH client. In order to do this, you must know the IP address of
the AOS device. If you do not know the unit’s IP address, you must use the
CONSOLE
port to access the CLI.
To access the CLI using a Telnet or SSH client, follow these steps:
1. Connect the NetVanta unit to your PC using an Ethernet cable connected to the unit’s switch port labeled
GIG 0/1
, or connect the NetVanta unit to an existing network that supports DHCP using the unit’s
GIG 0/
1
switch port.
2. Open a Telnet or SSH client on your computer and enter
10.10.10.1
. If your unit received an IP address
from a DHCP server, or you have changed your unit’s IP address, you will need to enter that address
instead.
3. For SSH, log into the unit using the default login (
admin
) and password (
password
). For Telnet, only the
default password (
password
) is required.
4. Enter
enable
at the
>
prompt and enter the enable password when prompted. The default password is
password
.
C
OMMON
CLI C
OMMANDS
The following are common CLI commands and tips for getting started with the CLI.
■ Entering a question mark (?) shows contextual help and options. For example, entering
?
at the prompt will
show all commands available from that prompt.
■ To view interface statistics, enter
show interfaces
<interface type>
<interface number>
.
■ To view the current configuration, enter
show running-config
.
■ To view all the IP Addresses currently configured, enter
show ip interfaces brief
.
■ To view the AOS version, serial number, and other information, enter
show version
.
■ To save the current configuration, enter
write
.
M
ANUALLY
C
ONFIGURING
THE
U
NIT
’
S
IP A
DDRESS
The following steps create an IP address (10.10.10.1 255.255.255.0) for Gigabit Ethernet port 0/1 (
GIG 0/1
). If
you are not sure what IP address to assign, please contact your network administrator.
g
NOTE
This step is unnecessary if the unit’s IP address has been configured automatically using DHCP
.
