ADTRAN NetVanta 1224STR PWR Скачать руководство пользователя страница 20

Страница: 20 / 48

Option Modules

NetVanta 1224STR DC Hardware Installation Guide

61200590E1-34B

Network Interface Modules

NetVanta 56K/64K NIM (P/N 1200861L1)

The 56K/64K NIM (shown in

Figure 3

) provides a DDS WAN interface for the NetVanta. This module provides

a single 56K or 64K DDS network interface. See

Table A-5 on page 45

for the WAN-DDS connector pinouts,

and

Table A-13 on page 48

for the DBU connector pinouts. An optional DIM is required for dial backup

applications.

Figure 3. NetVanta 56K/64K NIM

Features and Specifications

Operating Modes

•

Dedicated DDS (leased line)

DDS Interface

•

Supported Standards: AT&T TR 62310

•

4-wire, full-duplex

•

Receiver Sensitivity: -45 dB, all rates

•

Data Rates: 56K, 64K, and auto

•

Connector: RJ-48S

Clock Source

•

Network

•

Internal

Diagnostics

•

CSU and DSU Loopbacks

Compliance

•

EMC - see

Electromagnetic Compatibility

(EMC) Table on page 6

•

ACTA/FCC Part 68

•

IC CS-03

•

UL/CUL 60950

Environmental

•

Operating Temperature: 0°C to 50°C

•

Storage Temperature: -20°C to 70°C

•

Relative Humidity: Up to 95 percent,
noncondensing

Physical

•

Dimensions: 2.75-inch W x 4.25-inch D

Содержание NetVanta 1224STR PWR














































Результаты поиска

Содержание NetVanta 1224STR PWR

Отзывы:

Похожие инструкции для NetVanta 1224STR PWR

Бренды по названию

Популярные бренды

ADTRAN NetVanta 1224STR PWR, Руководство по установке оборудования

Результаты поиска

Содержание NetVanta 1224STR PWR

Отзывы:

Похожие инструкции для NetVanta 1224STR PWR

Бренды по названию

Популярные бренды