Quick Start Guide, 61200570L1-13C, November 2006
Copyright © 2006 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at
.
Quick Start Guide
®
NetVanta 1224 Power over Ethernet Series
P/N 1200530L1/1200570L1/
1200580L1/1200584L1
C
ONFIGURE
THE
U
NIT
’
S
IP A
DDRESS
The following steps create an IP address and subnet mask for the virtual interface
vlan 1
. If you are
not sure what IP address to assign, please contact your network administrator.
1.
At the
#
prompt, enter
config terminal
.
2.
At the
(config)#
prompt, enter
interface vlan 1
to access the configuration parameters for the
virtual LAN (VLAN) interface.
3.
Enter
ip address 10.26.12.12 255.255.255.0
to assign an IP address to the VLAN interface
using a 24-bit subnet mask.
4.
Enter
no shutdown
to activate the virtual interface to pass data.
5.
Enter
exit
to return to the Global Configuration mode.
E
NABLE
T
ELNET
A
CCESS
The following steps create a password of
adtran
for Telnet access. By default, Telnet access is
enabled with a password of
password
.
1.
Verify that the prompt of your unit displays
(config)#
.
2.
Enter
line telnet 0 4
to change the configuration parameters for the Telnet sessions.
3.
Enter
login
to initiate Telnet access.
4.
Enter
password adtran
to change the login password for the Telnet sessions.
5.
Enter
exit
to return to the Global Configuration mode.
6.
Verify that the prompt of your unit displays
(config)#
.
7.
Enter
do write memory
to save the current configuration.
The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all
underlined entries (
example
) with your specific parameters to configure
your application.
Depending on your configuration, you may need to set a default gateway
as well using the
(config)#ip default gateway
command. If IP routing is
enabled on the unit, do NOT set a default gateway.
This note does not apply to the NetVanta 1224R PoE or 1224STR PoE
units with integrated routers.
For information on installing the VPN Accelerator Card, please refer to
the
NetVanta 1000 Series Hardware Installation Guide
on the
ADTRAN OS System Documentation
CD included in your switch
shipment.
C
ONFIGURE
Y
OUR
A
PPLICATION
More detailed documentation for configuring your ADTRAN unit is provided on the
ADTRAN OS
System Documentation
CD included in your shipment. For more detail on hardware setup, refer to
the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on
configuring your system, refer to the
ADTRAN Operating System (AOS) Command Reference
Guide
, configuration guides, and technical support notes.
E
THERNET
P
INOUTS
Pin
Name
Description
1
TX1
Transmit Positive
2
TX2
Transmit Negative
3
RX1
Receive Positive
4, 5
—
Unused
6
RX2
Receive Negative
7, 8
—
Unused
C
ONSOLE
P
INOUTS
Pin
Name
Description
1
DCD
Data Carrier Detect (output)
2
RD
Receive Data (output)
3
TD
Transmit Data (input)
4
DTR
Data Terminal Ready (input)
5
SG
Signal Ground
6
DSR
Data Set Ready (output)
7
—
Unused
8
CTS
Clear to Send (output)
9
—
Unused
Important:
For additional details on product features, specifications,
installation, and safety, refer to the appropriate Hardware Installation
Guide on the
ADTRAN OS System Documentation
CD shipped with the
base unit and available online at www.adtran.com.
