PRICING AND AVAILABILITY 800.827.0807
TECH SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61186002L1-22E
Warranty
: ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at
www.adtran.com/warranty
.
1. Configuration
2. Provisioning
3. Status
4. T
est
5. Performance Monitoring
4. Protection
Note: An asterisk (*) indicates default setting
5. Save Provisioning
1. 0-133 ft*
T1:
E1:
3. 266-399 ft
2. 133-266 ft
5. 533-655 ft
1. 0-6dB Loss
4. 399-533 ft
1. 2 seconds*
29. Set Multiple
30. Auto Enable Delay
3. 2 hours
2. 1 hour
5. 1 day
4. 12 hours
6. 2 days
7. 7 days
1. Disabled
3. 5 Minutes*
2. 1 Minute
5. 15 Minutes
4. 10 Minutes
6. 30 Minutes
7. 45 Minutes
8. 60 Minutes
1. Near End Daily
3. Far End Daily
2. Near End Quarter Hourly
5. Near End Daily Thresholds
4. Far End Quarter Hourly
6. Near End Quarter Hourly Thresholds
7. Near End Daily Thresholds
8. Near End Quarter Hourly Thresholds
9. Clear DS3 Statistics
1. Data Mode*
3. Digital Loopback
2. Line Loopback
5. Remote ALL
T1/E1
4. Remote Loopback
1. QRSS*
3. ALL
ZEROES
2. ALL
ONES
5. 1 in 8 (1:7)
4. 2 in 8 (2:6)
6. 2 ^15-1 INV
1. Data Mode*
2. Network Loopback
1. Data Mode*
T1:
3. Analog Network
2. T
ributary
5. CODEC Line/Net
4. Digital Line/Net
6. Remote Loopback
7. LS CSU Loopback
8. LS CSU LB w/BER
T
9. LS NIU Loopback
10. LS NIU LB w/BER
T
1
1
. LS Line BER
T
1. Data Mode*
E1:
T1/E1 Loopbacks (T1/E1 #1-28)
29. DS3 Loopbacks
3. Analog Network
2. T
ributary
5. CODEC Line/Net
4. Digital Line/Net
6. Remote Loopback
7. LS Line BER
T
CLEI Code
Serial Number
Part Number
Code Checksum
Code V
ersion
Boot V
ersion
Boot Checksum
Self T
est
1. Disabled*
3. 1E-4
2. 1E-3
5. 1E-6
4. 1E-5
1. Disabled*
3. 1E-4
2. 1E-3
5. 1E-6
4. 1E-5
1. Near End Daily
3. Near End Daily Thresholds
2. Near End Quarter Hourly
4. Near End Quarter Hourly Thresholds
5. Clear T1/E1 Statistics
1. Disabled
3. FEAC
2. FEAC/C-BIT*
4. C-BIT
1. DS3 Framing
3. DS3 Remote Loopbacks
2. DS3 T
iming
7-13. DS2 Mode (DS2 #1-7)
4. DS3 XCV Threshold
1. T1/E1 State
3. T1/E1 Line Length
2. T1/E1 Line Coding
5. T1/E1 Circuit Protection
4. T1/E1 Loopback Detection
6. T1/E1 Line Identification
7. T1/E1 XCV Threshold
(T1/E1 #1-28)
(T1/E1 #1-28)
(T1/E1 #1-28)
(T1/E1 #1-28)
(T1/E1 #1-28)
7. Card Reset
1. Network Interface
2. T1/E1 Interfaces
3. Service States
6. Restore Factory Defaults
8. Auto Save
9 . Loopback T
imeout
10 . Card Pair ID
1. AMI
2. B8ZS/HBD3*
1. Disabled
2. Enabled
3. Auto Enable*
T1/E1 #1-28
29. DS3
30. Set Multiple
1. Card
n
A
2. Card
n
B
3. Facility Service States
2. Enabled*
1. Disabled
30. Protection Threshold (1-28): 1*
2. Enabled*
1. Disabled
1. Disabled*
2. CSU (T1 Only)
3. NIU (T1 Only)
1. Perform Manual Switch
2. Minimum Switching Period (sec.) (10*)
3. Maximum Switch Threshold (3*)
1. DS3 Statistics
2. T1/E1 Statistics
3. Clear ALL
Statistics
1. M12 (4xT1)*
2. G.747 (3xE1)
1. C-BIT
2. M13*
1. IS*
2. OOS
1. Loop
2. Local*
30-36. DS2 #1-7 Loopbacks
37. Reset ALL
T
ests
38. Pattern
14. DS3 Equipment Identification
(T1/E1 #1-28)
12. HS CSU Loopback
13. HS CSU LB w/BER
T
14. HS NIU Loopback
15. HS NIU LB w/BER
T
16. HS Line BER
T
5. IP
Forwarding Protocol
6. IP
Forwarding MTU
1. ADTRAN*
2. PPP
1. 260 (PREFERRED)*
4. Clear Number of Switches
8. HS Line BER
T
2. 1500
29. Set Multiple
(T1/E1 #1-28)
MX2820 M13 MUX
