2
61442985G1C-22A
NOTICE
It is recommended that the protective end cap remain on
whenever the transceiver optical fiber connector is not inserted.
Continue the installation and turn-up of the host module using
the instructions in the Job Aid provided with the module or other
system-level documentation available online at
www.adtran.com
.
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
C
This product uses a Class 1 Laser module that complies with 21
CFR 1040.10 and 1040.11 and IEC 60825-1, IEC 60825-2, EN 60825-
1 and EN 60825-2. For continued compliance with the above
standards, only approved Class 1 laser modules from an
ADTRAN approved vendor list (located on the ADTRAN
website) should be installed in this product. ADTRAN cannot
certify system integrity with other laser modules.
CAUTION
!
•
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
•
Per GR-1089-CORE the system is designed and intended for
installation as part of a Common Bonding Network (CBN).
The system is not designed nor intended for installation as
part of an Isolated Bonding Network (IBN).
•
Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. This product can be installed in a DC-I (isolated) or
DC-C (common) installation. For installations where other
cards or the host system have internal connections between
battery return and frame ground, the system would be
intended for deployment only in a DC-C installation.
•
The chassis frame ground terminal must be connected to an
earth ground to ensure that the metal enclosure of the XFP is
properly grounded via the backplane connector.
NOTE
•
The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
•
The Tunable XFP is compliant with SFF-8472 “Digital
Diagnostics Monitoring Interface for Optical Transceivers,”
Revision 9.3.
•
The Tunable XFP is compliant with the XFP Multi-Source
Agreement (MSA).
•
The Tunable XFP is designed to be deployed in GR-3108-
CORE environmental class 1 as defined in GR-3108-CORE.
This product is NRTL Listed to the applicable UL Standards. The
product is designed to meet the applicable requirements of
Telcordia GR-63-CORE, and GR-1089-CORE.
This product has also been evaluated to international safety
standards EN 60950-1, AS/NZS 60950.1, and IEC 60950-1. This
product meets the requirements for CE marking under the EMC
Directive and Low Voltage Directive. Standards used to demon-
strate Compliance are EN 300 386 and EN 60950. The Tunable
XFP is intended for deployment in Central Office (Telecommuni-
cation Center) type facilities, EEEs, EECs Access or Trunk
Network Locations), and locations where the NEC applies (for
example, Customer Premises).
The Tunable XFP is to be installed in ADTRAN products in
Restricted Access Locations only, and installed by trained service
personnel.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.
The product also complies with ETSI EN 300 386 “Electromag-
netic compatibility and Radio spectrum Matters (ERM); Telecom-
munication network equipment; Electromagnetic Compatibility
(EMC) requirements.”
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
The Tunable XFP is designed to meet the following environ-
mental classes:
•
ETSI EN 300 019-1-1 “Classification of environmental
conditions; Storage,” Class 1.2
•
ETSI EN 300 019-1-2 “Classification of environmental
conditions; Transportation,” Class 2.3
•
ETSI EN 300 019-1-3 “Classification of environmental
conditions; Stationary use at weather-protected locations,”
Class 3.2
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.2.
The 10G DWDM Tunable XFP meets EU RoHS Directive 2002/
95/EC and/or applicable exemptions. Refer to
www.adtran.com
for further information on RoHS/WEEE.
