C A U T I O N
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Warranty
: ADTRAN will replace or repair this product
within the warranty period if it does not meet
its published specifications or fails while in
service. Warranty information can be found
online at
.
©2013 ADTRAN, Inc. All Rights Reserved.
*61442910G2-22A*
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
Read all warnings and cautions before installing or servicing
this equipment.
CAUTION
C
This product is a Class 1 Laser Product and complies with the
Laser Safety requirements of FDA 21CFR 1040.10 and 1040.11,
and EN60825-1 and -2. The XFP is NRTL listed and CB Certified
to all applicable American and European safety standards.
For continued compliance with the above laser safety standards,
only approved Class 1 modules from our approved vendor list,
located on the ADTRAN website, should be installed in ADTRAN
products.
CAUTION
!
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
This product meets or exceeds all the applicable requirements
of NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. This
product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises). This product is to be
installed in ADTRAN products in Restricted Access Locations
only, and installed by trained service personnel.
Per GR-1089-CORE, the ADTRAN system in which this
product is being deployed is designed and intended for
installation as part of a Common Bonding Network (CBN).
The ADTRAN system in which this product is being deployed
is not designed nor intended for installation as part of an
Isolated Bonding Network (IBN).
Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. The XFP can be installed in a DC-I (isolated) or DC-C
(common) installation. For installations where other cards or
the host system have internal connections between battery
return and frame ground, the system would be intended for
deployment only in a DC-C installation.
The ADTRAN system chassis frame ground terminal must be
connected to a reliable earth ground to ensure that the metal
enclosure of this product is properly grounded via the
backplane connector.
NOTE
The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE Issue 6.
This product is designed to meet the following environmental
classes:
GR-3108-CORE Environmental Classes 1, 2, and 3.
ETSI EN 300 019-1-1 “Classification of environmental
conditions; Storage,” Class 1.2
ETSI EN 300 019-1-2 “Classification of environmental
conditions, Transportation,” Class 2.3
ETSI EN 300 019-1-3 “Classification of environmental
conditions, Stationary use at weather-protected locations,”
Class 3.3
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.3.
This device complies with FCC 47 CFR Part 15, Class B. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
