job
Aid
D
ESCRIPTION
The 8 Gigabit Fibre Channel 10 Km XFP, 1310 nm (XFP) optical
transceiver is a fully duplex serial electric, serial optic device. It
has both transmit and receive functions and provides a high
speed serial link at 8.5 Gb/s. Installed into an appropriate host
module, the XFP provides a 8 Gigabit interface to the supporting
system.
The transmit side of the XFP converts serial NRZ electrical data at
the 8.5 Gb/s line rate to a standard compliant optical signal. The
receive side of the XFP converts the incoming DC balanced serial
NRZ optical data at the 8.5 Gb/s line rate into serial electrical
data.
NOTE
To ensure compatibility, refer to the ADTRAN documentation
provided with the host module.
The XFP has the following features:
1310 nm optical signals for up to 10 km reach
Low power consumption (<2.0 W max for 10 km)
Bit error rate (<1x10
-12
)
Excellent EMI performance
CAUTION
!
Due to compliance certification requirements, use only XFPs
supplied by ADTRAN with the host module. ADTRAN cannot
certify system integrity with other XFPs.
Small Form-Factor Pluggable
8 Gig
abit Fibre Channel 1310 nm 10 km XFP
Operational Specifications
Optical Specifications:
o
Transmit wavelength: 1260 to 1355 nm (1310 nm nominal)
o
Receive wavelength: 1260 to 1600 nm
o
Data rate: 8.5 Gb/s (8G Fibre Channel)
o
Optical transmit level: –8.2 to +0.5 dBm
o
Optical receive level: –14.4 to +0.5 dBm
o
Optical distance: 10 km maximum
o
Optical connectors: LC
Extended Environmental Support:
o
Operational temperature range: –40°C to +85°C
o
Storage temperature range: –40°C to +85°C
o
Relative humidity to 85%, noncondensing
I
NSTALLATION
Inspect the XFP. If damaged, file a claim with the carrier and then
contact ADTRAN Customer Service.
To install the XFP into an appropriate module, complete the
following steps:
1. Insert the XFP into the XFP cage on the circuit board of the
host module with the latch handle facing outward. Slide the
XFP all the way into the receptacle.
NOTE
The latch on the XFP is for removal only. When removing the
XFP, rotate the latch away from the XFP cage until a physical click
occurs. The XFP should slide easily out of the cage.
2. Using thumb and forefinger, exert adequate pressure to
ensure the XFP is completely seated in the XFP cage.
3. Do not remove the connector plug until the optical fiber
connection is made.
NOTICE
We recommend that the connector plug remain on whenever the
transceiver optical fiber connector is not inserted.
4. Continue the installation and turn-up of the host module
using the instructions in the Job Aid provided with that
module, or by using the applicable Total Access 5000 Series
Deployment Guide or User Interface Guide, available online
at
www.adtran.com
.
CLEI: BVL3AXPD__
Product P/N: 1442910G2
Issue Date: November 2013
Document P/N: 61442910G2-22A
Documentation for ADTRAN Carrier Networks products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to:
https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to:
http://adtran.com/training
The following documents provide additional information for this product:
SFP/XFP/SFP+ Compatibility Matrix and Engineering Guide
