ADTRAN DS3-PSM Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 138

ADTRAN DS3-PSM Скачать руководство пользователя страница 65

Menu Trees

61181041L3-5A

55

ATM Provisioning Screen - Shelf # Slot # Port # (PNNI Port Options) Menu
The ATM Provisioning Screen - Shelf # Slot # Port # (PNNI Port Options) menu (see

)

is used to set port parameters for Private Network-to-Network Interface (PNNI) interoperability.

Figure 28. ATM Provisioning Screen - Shelf # Slot # Port # (PNNI Port Options) Menu

The ATM Provisioning Screen - Shelf # Slot # Port # (PNNI Port Options) menu options are
shown in

Table 28. ATM Provisioning Screen - Shelf # Slot # Port #

(PNNI Port Options) Menu Options

Option

Description

Function

1

Allow SVCs

This option is used to allow or prohibit Switched Virtual
Circuits (SVCs).

2

Aggregation token

This option is used to set the Aggregation token value to a
number from 0 to 4294967295.
The Aggregation token is number assigned to an outside link
by the border nodes at the ends of the outside link. The
same number is associated with all uplinks and induced
uplinks associated with the outside link. In the parent and
all higher-level peer group, all uplinks with the same Aggre-
gation token are aggregated.

3

Admin weight CBR

This option is used to set the Admin weight Constant Bit
Rate (CBR) value to a number from 1 to 16777215. The
administrative weight is used to indicate the relative
desirability of using a link or node for whatever reason
significant to the network operator.

Shelf: 1 Slot: B Total Access System MM/DD/YY HH:MM
ONLINE

                         ATM PROVISIONING SCREEN
                         Shelf: 1 Slot 1 : Port  1
         1.  Allow SVCs           : YES
         2. Aggregation token     : 0
         3. Admin weight CBR       : 5040
         4. Admin weight RT VBR    : 5040
         5. Admin weight NRT VBR   : 5040
         6. Admin weight UBR       : 5040
         7.  Service classes       : CBR + rtVBR + UBR
         8.  VP connections allowed : NO
         9.  Allow SPVC connections : NO
         10. Auto address setup

Selection:

«
...
63
64
65
66
67
...
»

Содержание DS3-PSM











































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды