job
Aid
D
ESCRIPTION
The
OC
‐
12
Small
Form
‐
Factor
Pluggable
CWDM
1491
nm
(SFP
OC
‐
12)
plugs
into
ADTRAN
OC
‐
12
equipment
designed
to
accept
Small
Form
‐
factor
Pluggables
(SFPs).
Installed
into
an
appropriate
host
unit,
the
SFP
OC
‐
12
provides
an
OC
‐
12
CWDM
interface
to
the
supporting
system.
NOTE
To
ensure
compatibility,
refer
to
the
documentation
provided
with
the
host
module.
The
following
features
are
supported
on
the
SFP
OC
‐
12:
♦
SONET
OC
‐
12
compatible
(622.08
Mb/s)
1491
nm,
long
reach,
single
‐
mode,
2
‐
fiber
operation
♦
80
km
maximum
optical
span
CAUTION
!
Due
to
compliance
certification
requirements,
use
only
SFPs
supplied
by
ADTRAN
with
the
host
module.
ADTRAN
cannot
certify
system
integrity
with
other
SFPs.
S
PECIFICATIONS
♦
Optical
Specifications:
◊
Optical
transmit
level:
–3
dBm
to
+5
dBm
◊
Optical
receive
level:
–28
dBm
to
–8
dBm
◊
Power
penalty:
–1
dB
◊
Optical
budget:
24
(±1)
dBm
◊
Minimum
span
attenuation:
13
dB
◊
Optical
connectors:
LC
♦
Extended
Environmental
Support:
◊
Operational
temperature
range:
–40°C
to
+65°C
◊
Storage
temperature
range:
–40°C
to
+85°C
◊
Relative
humidity
to
95%,
noncondensing
OC-12 Small Form-Factor Pluggable
CWDM 1491 nm
I
NSTALLATION
To
install
the
SFP
OC
‐
12
into
an
appropriate
module,
complete
the
following
steps:
1. Inspect
the
SFP
OC
‐
12.
If
damaged,
file
a
claim
with
the
car
‐
rier
and
then
contact
ADTRAN
Customer
Support.
CAUTION
!
Do
not
remove
the
protective
end
cap
from
the
SFP
until
the
fiber
optic
cable
is
ready
to
be
connected.
2. Insert
the
SFP
OC
‐
12
into
the
SFP
cage
on
the
module.
Ensure
that
the
manufacturer’s
label
on
the
SFP
is
facing
upward
for
correct
installation.
3. Slide
the
SFP
OC
‐
12
all
the
way
into
the
receptacle
until
there
is
an
audible
“click”.
NOTE
The
latch
on
the
SFP
is
used
to
remove
the
SFP
from
the
cage
on
the
circuit
card.
P
ROVISIONING
The
SFP
OC
‐
12
is not directly provisionable. To provision the
SFP
OC
‐
12
, access the menu system of the host module.
Refer to the “Provisioning” section of the Job Aid or I&M
provided with the host module for provisioning details.
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
CAUTION
!
Electrostatic
Discharge
(ESD)
can
damage
electronic
modules.
When
handling
modules,
wear
an
antistatic
discharge
wrist
strap
to
prevent
damage
to
electronic
components.
Place
modules
in
antistatic
packing
material
when
transporting
or
storing.
When
working
on
modules,
always
place
them
on
an
approved
antistatic
mat
that
is
electrically
grounded.
The
SFP
OC
‐
12
is
NRTL
Listed
to
the
applicable
UL
standards.
The
SFP
OC
‐
12
meets
or
exceeds
all
the
applicable
requirements
of
NEBS,
Telcordia
GR
‐
63
‐
CORE,
GR
‐
1089
‐
CORE,
and
ETSI
EN
300368.
The
SFP
OC
‐
12
is
intended
for
deployment
in
Central
Office
type
facilities,
EEEs,
EECs,
and
locations
where
the
NEC
applies
(for
example,
Customer
Premises).
The
SFP
OC
‐
12
is
to
be
installed
in
ADTRAN
products
in
Restricted
Access
Locations
only,
and
installed
by
trained
service
personnel.
CLEI: SOOTAKNJ_ _
Product P/N: 1442703PG2
Issue Date: December 2010
Document P/N: 61442703PG2-22B
