ADTRAN 1200080L1 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 38

background image

Chapter 3. Operation

20

FXS+ Dual Voice Option Module

61200.080L1-1

Fault Resp (Fault Response)

Fault Resp is used to set the 2-wire response to a carrier
alarm. For a network alarm, the ground start 2-wire
trunk would appear busy if Fault Resp is set to seized. If
set to normal, no seizure of a ground start trunk occurs.

Choices include:
• Normal
• Seized

Tandm Options (Tandem Options)

Some options are valid only when operating in the
tandem mode. These options are provided below.

• Supervision

Supervision sets the supervision method used when
the card is configured to operate in the Tandem mode.

Choices include:
- Immediate
- Wink

• Dial Tone

Dial Tone is used to enable or disable the on-board
dial tone generation when the FXS+ is operating in the
tandem mode. When the on-board dial tone genera-
tion is enabled, the dial tone will turn off after a five
second time-out.

Choices include:
- Enabled
- Disabled

•

Loop Reverse Battery

This option causes the polarity of tip and ring to be
reversed when the far-end answers and the FXS+ card
is set to TANDEM_LS mode. This provides answer
supervision to the 2-wire port.

Choices include:
- Enabled
- Disabled

«
...
22
23
24
25
26
...
»

Содержание 1200080L1







































Отзывы:

Нет отзывов

Похожие инструкции для 1200080L1

Бренд: Waycon Страницы: 4

Бренд: ZERO GRAVITY Страницы: 6

Бренд: NARGESA Страницы: 27

Бренд: Endress+Hauser Страницы: 28

Action Replay DSi

Бренд: Datel Страницы: 2

Бренд: FeiYu Tech Страницы: 14

Бренд: Xantrex Страницы: 3

ORBISPHERE K1200

Бренд: Hach Страницы: 104

Бренд: 3SIXT Страницы: 12

Бренд: W-Tec Страницы: 6

Бренд: Neuspeed Страницы: 2

Бренд: REV Страницы: 2

Бренд: Sonero Страницы: 32

USB 3.0 Dual Head Docking Station

Бренд: SIIG Страницы: 12

Бренд: Thunderbike Страницы: 11

Monarch Pass M321

Бренд: Wolfman Страницы: 5

Бренд: Wilco Offroad Страницы: 4

Бренд: minnid Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды