manualshive.com logo in svg

ADTEK AEM-DRB, Руководство по эксплуатации

Поделиться
Скачать
ADTEK AEM-DRB Скачать руководство пользователя страница 6

2

1.3 Warning & Criterion

•  Installation attention

•  Wiring attention

•  Operation attention

•  Beware  of  potential  hazards.  Wear  safety  equipment  properly 

when operating this device and follow safety standards and related 
regulations for operating electric equipment.

•  Installation  of  this  device  should  be  performed  by  licensed 

professionals. Perform operations only after carefully reading this 
manual.

•  Operate this device according to this manual to prevent improper 

operation that may cause damage and bodily harm.

•  This  device  should  be  installed  in  a  properly-insulated  fire-

protection cabinet.

•  When using the equipment,  potential transformer for secondary 

side is prohibited short circuit.

•  When using the equipment,  current transformer must not be under 

an open circuitaa.

•  When using the equipment,  please make sure current transformer 

for secondary side has been locked on the equipment. To avoid the 
main trunk line falling off during use, causing equipment damage.

•  When used with a current transformer (CT), please use a current 

transformer (CT) that meets UL2808 in the United States/Canada, 
and use a current transformer (CT) that meets the requirements of 
IEC61869-2 or AHJ in other countries to ensure use Safety.

•  Do not operate alone.
•  Power  should  be  disconnected  before  installing,  checking,  or 

maintaining this device.

•  You  must  use  a  voltage  checking  device  with  the  correct  rated 

values to ensure that all power has been disconnected.

•  Before connecting power, check that all mechanical parts, covers, 

and doors have been returned to their original states. Make sure 
there are no parts or tools left inside the device.

Содержание AEM-DRB













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды