Adtech ADTECH4 CNC Series Скачать руководство пользователя страница 61

Страница: 61 / 201

ADTECH4 SeriesCNC Maintenance Manual

Tool magazine parameters

Tool magazine parameters collect the parameters that the tool magazine requires. The specific meaning of

the parameters should be determined by the tool magazine of the machine tool, and therefore should refer to

the instructions provided by the machine tool manufacturer.

Principal axis parameters

Principal axis parameters are the set of electrical characteristics of servo and common principal axes. The

specific application also depends on the principal axis selection of the machine tool manufacturer. The servo

parameters and axis parameters have the same meaning, and therefore please refer to the description of axis

parameters.

Principal axis parameter interface is shown below:

Principal Axis Parameters Interface

IO configuration parameters

IO configuration parameters are the assignment of hardware interfaces. This parameter set is the IO pin

sequence specified by the system’s IO function numbers, which will improve the system flexibility. Please

refer to System Parameters for the specific meaning of the parameters.

IO configuration parameter interface is shown below:

Содержание ADTECH4 CNC Series










































































































































































































Результаты поиска

Содержание ADTECH4 CNC Series

Отзывы:

Adtech ADTECH4 CNC Series, Руководство по обслуживанию, Страница: 61 / 201

Результаты поиска

Содержание ADTECH4 CNC Series

Отзывы: