ADLINK Technology cPCIS-1100 Series Скачать руководство пользователя страница 40

Страница: 40 / 48

Power Supply Unit

Dielectric Withstand: Meets IEC950 regulation

EMI: Meets EN55022 / FCC Class A

Hold-up Time: 5mS after power fail signal

Remote ON/OFF: Available at [INH#] & [EN#] pins

Power Fail Signal: Available at [FAL#] pin

Status LED: <Green> means valid input voltage; <Amber> means a
critical fault.

Thermal Protection (OTP): Installed NTC and thermostat for thermal
sensor at [DEG#] pin

Power OK: Installed at all outputs

Leakage Current: Typ. 0.5mA

Output Characteristics

Output Current (A)

Output

Voltage

MIN.

MAX.

TYP.

PEAK.

MAIN +VO1

2.0 33.0 25.0

–

3.3V

AUX. +VO2

0 33 18 –

12V

AUX. +VO3

0 5.5 5.5 6

-12V

AUX. –VO4

0 1 0.5

1.5

Symbol:

" OVP built-in; "@" Adjustable; "#" Remote sensing;

" 3rd-wire Load Sharing; "=" Droop Current Sharing;

" Installed with Or-ing diode; "

" Magnetic Amplifier;

" Installed with Post-regulator; "

" Common Choke.

Remarks:

Peak load sustainable for less than 60sec. with duty cycle <10%.

Max. load is the continuous operating load of each rail. Max. load
of each rail cannot be drawn from all outputs at the same time.

Содержание cPCIS-1100 Series

















































Результаты поиска

Содержание cPCIS-1100 Series

Отзывы:

ADLINK Technology cPCIS-1100 Series, Руководство пользователя, Страница: 40 / 48

Результаты поиска

Содержание cPCIS-1100 Series

Отзывы: