ADLINK Technology CoreModule 740 Скачать руководство пользователя страница 31

Страница: 31 / 46

Chapter 3

Hardware

CoreModule 740

Reference Manual

Note:

The shaded areas denote power or ground. The signals marked with * indicate active low.

System Fan

Table 3-7

lists the pin signals of the optional System Fan header, which provides 2 pins with 0.079" (2mm)

pitch.

Note:

The shaded areas denote power or ground.

Power Interface

The CoreModule 740 requires one +5 volt DC power source and provides a 10-pin, shrouded header with 2

rows, odd/even pin sequence (1, 2), and 0.100" (2.54mm) pitch. If the +5VDC power drops below ~4.65V, a
low voltage reset is triggered, resetting the system.

The power input header (J7) supplies the following voltage and ground directly to the module:

•

5.0VDC +/- 5%

Note:

The shaded areas denote power or ground.

GND VGA

VGA Ground

CRT_VSYNC

Vertical Sync – Digital Vertical Sync Output to the CRT

VCC_CON_DAC

+5V Power and Ground for Digital to Analog Converter

Table 3-7. Optional System Fan Pin Signals (J6)

Pin #

Signal

Description

VCC

+5.0 volts DC +/- 5%

GND Ground

Table 3-8. Power Interface Pin Signals (J7)

Pin

Signal

Descriptions

GND Ground

+5V

+5 Volts

GND

Ground

+12V

+12 Volts routed to PC/104 and PC/104-Plus connectors

GND

Ground

+3.3V_PCI

+3.3 Volts routed to PCI

GND

Ground

+5V

+5 Volts

GND

Ground

+5V

+5 Volts

Table 3-6. Video Interface Pin Signals (J10) (Continued)

Pin # Signal

Description

Содержание CoreModule 740















































Результаты поиска

Содержание CoreModule 740

Отзывы:

Похожие инструкции для CoreModule 740

Бренды по названию

Популярные бренды

ADLINK Technology CoreModule 740, Справочное руководство

Результаты поиска

Содержание CoreModule 740

Отзывы:

Похожие инструкции для CoreModule 740

Бренды по названию

Популярные бренды