manualshive.com logo in svg

ADLINK Technology CoreModule 740, Справочное руководство

ADLINK Technology CoreModule 740 - комплексное решение на основе ARM Cortex-A7 процессора, обеспечивающее высокую производительность. Для подробной информации об использовании устройства, загрузите бесплатный Руководство по эксплуатации с нашего веб-сайта.

Поделиться
Скачать
background image

Chapter 3

Hardware 

20

Reference Manual

CoreModule 740

Speaker

The speaker signal provides sufficient signal strength to drive a 1W 8 

Ω

 “Beep” speaker through the Utility 

interface at an audible level. The speaker signal is driven from an on-board amplifier and the ICH8-M.

Reset Switch

The Utility 1 header provides the signal for an external reset button, which allows the user to re-boot the 

system.

HDD Activity LED

This indicator signal is fed to pin 69 of the Utility 1 connector to allow for an external LED to indicate IDE 

activity.

Battery Interface

An external battery input connection is provided through the Utility 1 interface to provide an external battery 
for the CMOS RAM and the RTC (Real Time Clock).

Utility 1 Pin Signals

Table 3-4

 lists the signals and their descriptions for the Utility 1 interface which provides a right-angle, 

80-pin connector with 0.025" (0.635mm) pin pitch.

Table 3-4.   Utility 1 Interface Pin Signals (J5)

Pin #

Signal

Description

1

DCD1*

Serial Data Carrier Detect 1 – Indicates external serial device is detecting a 
carrier signal (i.e., a communication channel is currently open). In direct connect 
environments, this is driven by DTR1 as part of the DTR/DSR handshake. 

2

PP_ STRB* Parallel Port Strobe – This is an output signal used to strobe data into the printer. 

I/O pin in ECP/EPP mode.

3

DSR1*

Serial Data Set Ready 1 – Indicates external serial device is powered, initialized, 
and ready. Used as hardware handshake with DTR1 for overall readiness. 

4

PP_AFD*

Parallel Auto Feed – This is a request signal into the printer to automatically 
feed one line after each line is printed.

5

RXD1

Serial Receive Data 1– Serial port 1 receive data in.

6

PD0

Parallel Data 0 – This signal provides parallel data to the printer.

7

RTS1*

Serial Request To Send 1 – Indicates port is ready to transmit data. Used as 
hardware handshake with CTS1 for low level flow control. 

8

PP_ERR*

Parallel Error – This is a status output signal from the printer. A Low State 
indicates an error condition on the printer.

9

TXD1

Serial Transmit Data 1 – Serial port 1 transmit data out.

10

PD1

Parallel Data 1 – This signal provides parallel data to the printer.

11

CTS1*

Serial Clear To Send 1 – Indicates external serial device is ready to receive data. 
Used as hardware handshake with RTS1 for low level flow control. 

12

PP_INIT*

Parallel Initialize – This signal is used to initialize printer. Output in standard 
mode, I/O in ECP/EPP mode.

13

DTR1*

Serial Data Terminal Ready 1 – Indicates port is powered, initialized, and ready. 
Used as hardware handshake with DSR1 for overall readiness to communicate. 

14

PD2

Parallel Port Data 2 – This signal provides parallel data to the printer.

Содержание CoreModule 740















































Отзывы:

Нет отзывов

Похожие инструкции для CoreModule 740

Supero P8SCT User Manual preview
P8SCT
Бренд: Supero Страницы: 92
TOHATSU AE4-30 Assembly Instructions Manual preview
AE4-30
Бренд: TOHATSU Страницы: 7
Raptor C1P9S01 User Manual preview
C1P9S01
Бренд: Raptor Страницы: 59
ASROCK Z170 Extreme7+ Technical Reference preview
Z170 Extreme7+
Бренд: ASROCK Страницы: 6
Xilinx ML505 Getting Started Tutorial preview
ML505
Бренд: Xilinx Страницы: 31
JETWAY M26GT4SVM User Manual preview
M26GT4SVM
Бренд: JETWAY Страницы: 19
ASROCK H55M-LE - - 01-2010 Installation Manual preview
H55M-LE - - 01-2010
Бренд: ASROCK Страницы: 181
SmartOne 74.226 Quick Start Manual preview
74.226
Бренд: SmartOne Страницы: 2
Infineon EVAL-IH-R5IPB-A-V1 User Manual preview
EVAL-IH-R5IPB-A-V1
Бренд: Infineon Страницы: 34
Gigabyte GA-H170M-HD3 DDR3 User Manual preview
GA-H170M-HD3 DDR3
Бренд: Gigabyte Страницы: 44
Gigabyte GA-X38-DS5 User Manual preview
GA-X38-DS5
Бренд: Gigabyte Страницы: 112
AOpen DX3R-U Easy Installation Manual preview
DX3R-U
Бренд: AOpen Страницы: 8
ASROCK P4I45PE User Manual preview
P4I45PE
Бренд: ASROCK Страницы: 31
Biostar BVK2A Manual preview
BVK2A
Бренд: Biostar Страницы: 84
ASROCK A330GC Brochure preview
A330GC
Бренд: ASROCK Страницы: 3
ASROCK A320TM-ITX Quick Installation Manual preview
A320TM-ITX
Бренд: ASROCK Страницы: 2
ASROCK A330ION Brochure preview
A330ION
Бренд: ASROCK Страницы: 5
ASROCK A230GC User Manual preview
A230GC
Бренд: ASROCK Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды